background image

9

Thank  you  for  purchasing  the  Jones  Light  Commercial  M achine.
I f  you  have  any  questions,  please  call  your  local  BodyCr aft  dealer
or  call  our  customer  ser vice  depar tment  at  800-990-5556.

Assembly  is  compl ete!  Please  take  the  following  steps  befor e  using  the
BODYCRAFT  JONES  M ACHI NE:

IMPORTANT

TIPS FOR PROPER AND SAFE USE

• ALWAYS utilize the Safety Spotters.  Failure to do so

can result in serious injury.

• Remember that the lifting bar is hooked into place by

rotating the bar toward the chromed hooks.

• Be certain that both hooks are fully engaged before

removing your hands from the lifting bar.

• Inspect the machine before every use.  Do NOT use

the machine if you find any irregularities.

• Be sure to register your warranty by submitting a

completed warranty registration form.

• This product must be assembled on a flat, level surface

to assure its proper function.

• If unsure about the proper use of the BodyCraft Jones

Machine, call your local BodyCraft dealer or our
customer service department at 800-990-5556.

WEI GHT L I M I TATI ONS FOR THE L I FTI NG BARS

JB7N  7’ Long, 35l  b. Steel with Nylon Ends. 500lbs Capacity

JB7PB 7' Long, 50 lb. Steel Power Bar, 1000 lb. Capacity.

JB7ABB 7' Long, 55 lb. Steel Power Bar, 1000 lb. Capacity.

Summary of Contents for Jones Light Commercial













Reviews: