background image

 

 

3. The Cool-Down Phase 

This stage is to let your Cardio-vascular System and muscles wind down. This is a repeat of the warm up exercise 

e.g. reduce your tempo, continue for approximately 5 minutes. The stretching exercises should now be repeated, 

again remembering not to force or jerk your muscles into the stretch. 

As you get fitter you may need to train longer and harder. It is advisable to train at least three times a week, and if 

possible to space your workouts evenly throughout the week. 

 
 

MUSCLE TONING 

To tone muscle while on your 

ELLIPTICAL STRIDER

 you will need to have the resistance set quite high. This will 

put more strain on your leg muscles and may mean you cannot train for as long as you would like. If you are also 

trying to improve your fitness you may need to alter your training program. You should train as normal during the 

warm-up and cool-down phases, but towards the end of the exercise phase you should increase the resistance by 

making  your  legs  work  harder  than  normal.  You  will  have  to  reduce  your  speed  to  keep  your  heart  rate  in  the 

target zone. 

 
 

WEIGHT LOSS 

The important factor here is the amount of effort you put in. The harder and longer you work the more calories you 

will burn. This is effectively the same as if you were training to improve your fitness, the difference being the goal. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  

 

 
 
 
 

Summary of Contents for BE-5920















Reviews: