Body Champ BRB2866 Owner'S Manual Download Page 15 | Manualshive

Page: 15 / 24

background image

BRB3785 BRB2866

Page 13

Assembly STEP 7

MONITOR ASSEMBLY

Remove the

Bolts (#16)

that are pre-assembled on the back of the

Monitor (#20)

, set them aside nearby.

Connect the

Hand Pulse Wire 1 (#35)

to the wire on the back of the

Monitor (#20)

. Then, attach the

Monitor (#20)

onto the bracket of the

Center Post (#02)

. Secure them together by using four

Screws (#20)

that were previously removed.

Hardware Required

THE ASSEMBLY PROCESS IS NOW COMPLETE.

However, for your own safety, please make sure to read this entire Owner’s Manual which includes safety

instructions and warnings, as well as any safety/warning labels affixed to the product before use. For your

safety, please visually and functionally inspect and test the unit after assembly is complete.

#16 Bolt (M5x10mm)

[4 pcs]

«
...
13
14
15
16
17
...
»

Summary of Contents for BRB2866

























Reviews:

No comments

Related manuals for BRB2866

AudioRider NTEX3196.1

Brand: NordicTrack Pages: 24

REX Orbi-Linear

Brand: SCIFIT Pages: 36

Brand: Scheinn Pages: 2

Brand: Pro-Form Pages: 24

Brand: Precor Pages: 54

Brand: Horizon Fitness Pages: 20

Brand: Horizon Fitness Pages: 164

Brand: BH Hipower Pages: 24

Brand: CycleOps Pages: 18

Brand: Christopeit Sport Pages: 28

Brand: Sparraw Pages: 37

Brand: CYBEX Pages: 88

Brand: Xebex Fitness Pages: 16

NordicTrack VU29

Brand: ICON Pages: 32

Brand: Ivation Pages: 5

Brand: Fitness Quest Pages: 13

Brand: Technogym Pages: 68

Brand: Weslo Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands