background image

•  The BOB Infant Car Seat Adapter is designed 

for use with single seat BOB Strollers and 
compatible Infant Car Seats. This product is 
not a universal adapter. Do not use with car 
seats and stroller models other than those 
specifi cally listed in the Stroller and Car Seat 
Compatibility charts listed on page 1. 

•   Children should not be placed directly in 

the BOB Stroller seat with the ICSA installed, 
unless tray is installed directly in front of 
child for safety and protection.

•  The ICSA Restraint Belt can interfere with 

proper function of the safety harness system.  
Additionally, the ICSA Accessory Bar can 
interfere with accessibility to the stroller 
seat.  Therefore, prior to placing child directly 
in stroller seat, the ICSA Restraint Belt and 
Accessory Bar must be removed from the 
stroller 

AND

 the Tray must be installed.  

Failure to do so may result in serious injury 
or death.

•   Read and understand all owner’s manuals 

and warnings for all BOB products used with 
the ICSA before use.

•   Read and understand infant car seat owner’s 

manual before use.

•   Always use seat harness of Infant Car Seat to 

avoid children falling out of stroller.

•   Refer to your Infant Car Seat owner’s manual 

for maximum capacity limitations and other 
safety warnings.

•   Follow assembly instructions. Failure to 

properly install this accessory product may 
result in accidents, severe injury or death. 
If you are not sure you can properly install 
this accessory, contact your BOB retailer and 
arrange for them to perform the installation.

•   Never leave children unattended in the 

stroller/infant car seat.

•   Always secure the infant car seat with the 

restraint belt when the car seat is placed in 
the stroller. Failure to do so may result in 
serious injury or death.

•   Always keep your Infant Car Seat handle 

in the vertical and locked position while in 
stroller, as extra protection for your child.

•   Stroller may become unstable if parcel bags 

are incorrectly attached or if bags other than 
those recommended by BOB Trailers, Inc. 
are used.

•   Do not run or jog when using the ICSA with 

car seat installed. Doing so may result in 
serious injury or death.

•   Do not use off -road or on uneven terrain 

when using the ICSA with car seat installed. 
Doing so may cause stroller to become 
unstable and result in accident, serious 
injury or death.

•   Children develop at diff erent rates. Consult 

with your pediatrician regarding the suit-
ability of the stroller use with your child. 

Infant Car Seat Adapter Warnings 

BOB IS NOT RESPONSIBLE FOR INJURY, DAMAGE OR FAILURE THAT RESULTS 

FROM OWNERS FAULTY ASSEMBLY OR MAINTENANCE AFTER SHIPPING.

OMA09D

P11

Summary of Contents for INFANT CAR SEAT ADAPTER













Reviews: