manualshive.com logo in svg

BMPRO J35A, Owner'S Manual, Page: 11 / 28

Share
Download
BMPRO J35A Owner'S Manual Download Page 11

11

ControlNode102

Figure 2:

 

The ControlNode102

 1

 3

 2

q

 PAIRING BUTTON

Button to enable Bluetooth pairing between the ControlNode102 and the JHub 
App on your own personal mobile device or JHub Tablet.

w

 LED STATUS INDICATOR

Indicates the operational/pairing status of the ControlNode102.

Table 5:

 ControlNode102 Operational Status and LED Flash Codes

*After memory has been cleared, the ControlNode102 LED Status Indicator will immediately flash 

green to enable pairing to a new mobile device.

Operational Status

Flashing Status Note

ControlNode102 is ready to pair

Green Flash 30 sec

ControlNode102 memory is full, 

cannot pair to any new mobile devices

Orange Flash 1 sec To pair to a new mobile device, clear 

the memory of the ControlNode102

Clearing ControlNode102 memory*

Red Flash 1 sec

Memory will only be cleared if the 

user presses and holds the Pairing 

Button for 10 seconds.

e

 CONTROLNODE SERIAL NUMBER

Required to choose the correct device when pairing the ControlNode102  
to the JHub App on your own personal mobile device or JHub Tablet.

Summary of Contents for J35A





























Reviews:

No comments