background image

iVolve Full Face Mask User Manual V1.

2 / 16 

En

g

lis

Before Using the Mask 

 

WARNINGS

 

 

The vent holes must be kept clear. 

 

Explanation of Warning:

 CPAP systems are intended to be 

used with special masks with connectors which have vent holes 
to allow continuous flow of air out of the mask. When the CPAP 
machine is turned on and functioning properly, new air from the 
CPAP machine flushes the exhaled air out through the 
attached mask exhalation port. However, when the CPAP 
machine is not operating, enough fresh air will not be provided 
through the mask, and exhaled air will be rebreathed. 
Rebreathing of exhaled air for longer than several minutes can, 
in some circumstances, lead to suffocation. This warning 
applies to most models of CPAP systems. 

 

At low CPAP pressures the flow through the exhaled port may 
be inadequate to clear all exhaled gas from the tube. Some 
rebreathing may occur.   

 

To minimize the risk of vomiting during sleep, the patient 
should avoid eating or drinking for three hours before using the 
mask. This mask is not recommended if the patient is taking a 
prescription drug that may cause vomiting.   

 

Do not use the mask without the Non-Rebreathing Valve in 
place. 

 

This mask should not be used on patients who are 
uncooperative, obtunded, unresponsive, or unable to remove 
the mask. 

 

Follow all precautions when using supplemental oxygen.

 

 

Oxygen flow must be turned off when the flow generator is not 
operating, so that unused oxygen does not accumulate within 
the flow generator enclosure and create a risk of fire.   

 

At a fixed flow rate of supplemental oxygen flow, the inhaled 
oxygen concentration varies, depending on the pressure 
settings, patient breathing pattern, mask, point of application 
and leak rate.   

 

The technical specifications of the mask are provided for your 

Summary of Contents for iVolve BMC-FM



















Reviews: