Drawer preparation
Bore rear hole
Pre-bore for locking devices
Attach locking devices
Mounting screws must go in at a precise
angle and locking device must sit flat against
the drawer bottom to ensure proper function
of the drawer
Part no.
NOTE:
Use of the
T65.1600.01
Concealed runner
template is highly recommended
Concealed runner template
T65.1600.01
*NOTE:
T59.K010M spacers, available separately, required for 15/32” and 1/2” thick sub-fronts only.
Tool set
T65.9000
2.5
mm bit with
extension chuck
Concealed runner
template
6
mm bit with stop collar
Drawer Requirements
Drawer Preparation and Adjustment
Height adjustment
Press up on adjustment tab and push toward
back of drawer.
Maximum
3
(1/8") rise of drawer front (tool-free)
Side-to-side adjustment
Rotate side-to-side adjustment left or right on
both locking devices. Drawer front moves in
the same direction as rotation.
Maximum
1.5
(1/16") to left or right (tool-free)
Drawer removal
Squeeze orange release
levers on locking devices
Pull drawer out and up
Insert drawer
Extend the runners fully.
Place the drawer on the
runners and close. The
locking devices automatically
engage with the runners.
Make adjustments if
necessary.
Tilt adjustment
Rotate the tilt adjustment lever on the rear of
each runner to tilt the top of the drawer front
forward.
Maximum
5
(3/16") rise of drawer back (tool-free)
Adjustment and Removal
1
2
75°
locking
device
screws
606N
Drawer back preparation
Drawers
must
have
6
holes drilled in the
back panel to accept the hooks on the
MOVENTO runners. Drawers must also be
notched in the back, flush with the drawer
sides and drawer bottom.
NOTE:
Detailed drawings for recommended
drawer construction are available at blum.com
Dimensions in millimeters
(inch equivalents as noted) – Technical specifications subject to change without notice
For more information about installing Blum products, please visit blum.com or call 1-800-438-6788 for customer service
© 2018 Blum, Inc.
7
(9/32")
11
(7/16")
Ø
6 x 10
Bore for hook
50
(1-15/16") Minimum rear notch
13
(1/2")
Waste/recycle set
Minimum
opening width
Inside drawer
width
For drawer side thickness
16
(5/8")
15
(19/32”)
13
(1/2”)
12
(15/32”)
769R5337SB
305
(12")
263
(10-11/32")
295
(11-5/8")
293
(11-17/32")
289
(11-3/8")
287
(11-5/16")
769R5337SD
381
(15")
339
(13-11/32")
371
(14-19/32")
369
(14-17/32")
365
(14-3/8")
363
(14-9/32")
769R5337SF
457
(18")
415
(16-11/32")
447
(17-19/32")
445
(17-17/32")
441
(17-3/8")
439
(17-9/32")
NOTE:
Drawer length is
533
(21") for all sets.
Outside drawer width
Dimensions
NOTE:
Drawer side material thickness may vary. Accurate measurement of drawer side material
thickness should be used when calculating outside drawer width using the table below. Inside
drawer width
must
equal opening width minus
42
for MOVENTO to align and function optimally.
Minimum
top clearance
7
(9/32")
Outside drawer width
bottom clearance depending
on cabinet bottom recess
Opening width
Opening height
Maximum height
with bin =
Opening height
minus
13
(1/2")
21
(13/16")
aw
Inside dr er width
28
(1-3/32")
21
(13/16") Maximum
Important
Bin width and height must be considered
when designing your cabinet. (See the
diagram on the left.)
Minimum inside cabinet depth
With SERVO-DRIVE
577
(22-23/32")
Without SERVO-DRIVE
564
(22-7/32")
1
2
spacer*
Concealed runner
template