BlueStar Infra-Red Salamander BG3617 Installation & Operating Instructions Manual Download Page 18

 
 
 
 
 
 
 

                       MAINTENANCE 
 
 

A program

 

of proper cleaning techniques will aid in continued trouble free 

operation of this or any Quality equipment

 

                                     DAILY 

The Grid Rack should be wiped daily while still warm, using a heavy cloth or other 
grease absorbing material to remove grease and burnt food before they burn into the 
grid. Remove burnt materials, such as carbonized grease or food, with a stiff wire 
brush. 

DO NOT USE ANY TYPE OF STEEL WOOL.

 

Small particles may be left on the grid surface and get into the food products. Grid 
rack should be washed thoroughly using a wire brush and a hot, mild detergent or 
soap solution. Rinse with clear, warm water. 
 

             EXTERIOR AND INTERIOR CLEANING 
 

                       Establish a regular cleaning schedule. Any spills should be wiped 
                       Up immediately. 

 

1.  Wipe exposed, clean-able surfaces when cool with a mild detergent and hot 

water. Stubborn spots may be removed with a lightweight non- metallic 
scouring pad. Dry thoroughly with a clean cloth. 

 

2.  Stainless steel should be cleaned using a mild detergent, a soft cloth and hot 

water. If it is necessary to use a non- metallic scouring pad, always rub in the 
direction of the grain in the metal to prevent scratching. Use water based 
stainless steel cleaner (such as Drackett Twinkel), if you want a high shine. 

 
3.  To remove the inner rack assembly, place lift handle in the lowest position, 

pull the rack out as far as it will go. Remove the rack, and then remove the 
drip chute and set aside. Push the rack assembly back into the unit as far as it 
will go. Position the lift handle into the # 2 position. Carefully push down on 
the rack handle, which should allow the rear rollers to lift up and out of the 
roller guides. Now roll the rack assembly forward till you can grab it with 
both hands to remove it completely. Once you clean the rack assembly and are 
ready to re-install repeat the steps in reverse order. 

               

 

IMPORTANT - THESE INSTRUCTIONS ARE TO REMAIN WITH THE 
APPLIANCE AND THE CONSUMER IS TO RETAIN THEM FOR FUTURE 
REFERENCE 
 
 

PAGE 16

 

Summary of Contents for Infra-Red Salamander BG3617



















Reviews: