Blueridge BM18M23C Installation Manual Download Page 4

Revised 5/14/2020

1

WARNING

WARNING

Page 4 

Safety Precautions

Read Safety Precautions Before Installation

Incorrect installation due to ignoring instructions can cause serious damage or injury.

The seriousness of potential damage or injuries is classified as either a 

WARNING 

or

 

CAUTION

.

Failure to observe a warning may result in death. The appliance must be installed in

accordance with national regulations.

Failure to observe a caution may result in injury or equipment damage.

This symbol indicates that you must never perform the action indicated.

1.  Carefully read the Safety Precautions before installation.
2.  For commercial applications, such as restaurant kitchens, server rooms, etc., the use of 

specially designed air-conditioning units is highly recommended.

3.  Only trained and certified technicians should install, repair and service this air conditioning 

unit.

4.  Improper installation may result in electrical shock, short circuit, leaks, fire or other damage 

to the equipment and personal property.

5.  Strictly follow the installation instructions set forth in this manual.
6.  Before you install the unit, consider strong winds, typhoons and earthquakes that might 

affect your unit and locate it accordingly.

7.  Do not use means to accelerate the defrosting process or to clean, other than those 

recommended by the manufacturer.

8.  This appliance is not intended for use by persons (including children) with reduced physical, 

sensory or mental capabilities or lack of experience and knowledge, unless they have been 

given supervision or instruction concerning use of the appliance by a person responsible for 

their safety.

9.  Children should be supervised to ensure that they do not play with the appliance.
10.  An all-pole disconnect device must be incorporated in the high voltage wiring in accordance 

with local and national electrical codes.

11.  Any person who is involved with working on a refrigerant circuit should hold a current valid 

certificate from an industry-accredited assessment authority.

12.  Servicing shall only be performed as recommended by the equipment manufacturer.
13.  Maintenance and repair should be carried out by qualified personnel.
14.  Keep ventilation openings clear of obstruction.
15.  Do not turn on the power until all work has been completed.
16.  When moving or relocating the air conditioner, consult experienced service technicians for 

disconnection and reinstallation of the unit.

CAUTION

Summary of Contents for BM18M23C


























Reviews: