background image

Care and 

 

Maintenance

Page 9 

Revised 5/14/2020

•  Before changing the filter or cleaning, 

turn off the unit and disconnect its power 

supply.

•  When removing filter, do not touch metal 

parts in the unit. The sharp metal edges 

can cut you.

•  Do not use water to clean the inside 

of the indoor unit. This can destroy 

insulation and cause electrical shock.

•  Do not expose filter to direct sunlight 

when drying. This can shrink the filter.

CAUTION

•  Any maintenance and cleaning of 

outdoor unit should be performed by an 

authorized dealer or a licensed service 

provider.

•  Any unit repairs should be performed by 

an authorized dealer or a licensed service 

provider.

CAUTION

Maintenance – Long Periods of Non-Use

Maintenance – Pre-Season Inspection

If you plan not to use your air conditioner for an 

extended period of time, do the following:

After long periods of non-use, or before periods 

of frequent use, do the following:

If using a vacuum cleaner, 

the inlet side should face 

the vacuum. 

If using water, the inlet side 

should face down and away 

from the water stream. 

Turn on FAN function until 

Clean all filters

unit dries out completely

disconnect the power 

Turn off the unit and

 

Remove batteries  

from remote control

Check for damaged wires

Clean all filters

Check for leaks

Replace batteries

Make sure nothing is blocking all air inlets and outlets

Summary of Contents for BM12MCD





























Reviews: