manualshive.com logo in svg

Blue Wave MONTAUK NB19836, Instruction Manual

Share
Download
Blue Wave MONTAUK NB19836 Instruction Manual Download Page 20

20

INSTALLING THE SKIMMER

INSTALLATION OF THE FILTRATION SYSTEM

FILLING THE POOL WITH WATER

•  For protection and safety, all edges of the skimmer and return fitting windows must be covered by 

vinyl tape or rust proofing paint.

•  Follow the skimmer manufacturer’s instructions for skimmer installation.

ATTENTION: FOLLOW ALL SAFETY WARNINGS INCLUDED IN FILTRATION SYSTEM 

INSTALLATION MANUAL.

•  Follow the manufacturer’s instructions for installation of the filtration system. Once all of the hoses 

are attached to the skimmer and return fitting, finish filling the pool.

•   Before filling the pool with water, thoroughly check to see if there are any loose screws not 

tightened during the pool frame installation process. Also check for holes or tears in the liner. 

•  Fill the pool until the water is halfway up the skimmer opening or a minimum of 6-in (15-cm) from 

the top of the pool wall (see diagram 35). This will ensure water is entering the skimmer opening 
and flowing into the filter system. 

SAFETY WARNING!

 To avoid pool collapse, never leave the pool empty without water!  

The warranty does not cover damage to an empty pool.

Make sure pool waterline is 
6-in (15-cm) below the top 
of the pool wall.

(Diagram 35)

Summary of Contents for MONTAUK NB19836

























Reviews:

No comments

Brands by name

Popular brands

Load more brands