background image

standard recommended specifications for the pH- and chlorine value). It is equipped with
a tank drainage system, pressure gauge, built-in container components, e.g. bottom
laterals for even water distribution. The filter tank comes ready to attach and is supplied
with a user-friendly 7 Position Multi-Port Valve attached to the tank cover,

an approved

filter pump with hair and lint basket, and a plastic base for ready on- site mounting.

Read this manual carefully before installation. The filtration system and pump must be
installed in accordance with all federal and local codes and standards in effect for the area
of installation.
We decline all responsibility for the consequences of failure to comply with the installation
instructions. We recommend that you comply with the power source instructions to avoid
overloading the pump motor and/or electric shock.
This filtration system is not intended for use by persons with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge.
Safety notes and information boxes should always be observed.

C

.

Safety Notes

Your filter pump was constructed and tested and left the manufacturing plant in technically
operational condition. In order to maintain this condition and ensure safe operation, the
user should observe the notes and product information contained in this technical manual.
If there is any indication that safe operation is no longer possible, the device is to be
disconnected from the power supply and secured against accidental use.
This is the case when:

The device has visible damage.

The device no longer appears functional.

After long periods of storage in poor conditions.

If the power cord or other parts of this equipment are damaged, they have to be replaced
by manufacturer or its service agent or a similarly qualified person in order to avoid
danger.

D

.

Damage during delivery

Your filter system has been carefully and professionally packed for delivery. Please check
to ensure that the package is undamaged and that all parts are in the box. If you
purchased this product on order and the product was shipped to you, ensure that delivery
is complete. Damage to product as a result of shipping is not the responsibility of the
supplier and must be immediately reported to the shipper. The shipper assumes the
liability for damages during delivery, the supplier is not responsible for it.

E

.

Implied Warranty

The manufacturer warranties safe operation and reliability only under the following
conditions:

The filter system is installed and operated according to the assembly and operating
instructions.

Only original replacement parts are used for repairs or replacements (consumable &
expendable parts do no fall under the warranty).

Expendable parts that do not fall under the warranty include:

All O-rings

Pressure gauge

Page 03

Summary of Contents for FlowXtreme Pro NE4490













Reviews: