11
SMW 15
2.1
INSTALLATION (Fig. 5)
-
After having removed the packing, check that the
machine is in a perfect condition and that all the parts
have been included.
-
Position the machine in the required setting and level
it by means of the feet (11).
2.1.a Drain pipe connection (Fig. 5)
-
Connect one end of the drain pipe to the overflow
(12) and the other to an already prepared drain trap.
IMPORTANT
It is essential to ensure that the drain pipe runs along the
floor and that it is not throttled in any part.
2.1.b Connection to the water main (Figs. 5-6)
-
Connect one end of the supplied inlet pipe (13) to the
solenoid valve (14) and the other end (13) to a 3/4” G
threaded cock, installing the filter (15 Fig. 6) in between.
ATTENTION
It is essential to connect the cold water delivery pipe to a
throttle cock in order to separate the water main from the
machine itself. Also check that there are no sharp bends.
If there is sand in the water main, it will be necessary to
install a filter between the water main and the machine. If
the water main is without, it is advisable to install a
decalcifier prior to the machine with a setting of min. 4 and
max. 8 French degrees.
The manufacturer declines all responsibility for
damage to the machines caused by failure to comply
with the above listed provisions.
2.1.c Electrical connection (Fig. 5-6)
DANGER
-
Before connecting to the electricity main, always
check that the data pertaining to the power source
correspond to those indicated on the identification
plate ( 9 Fig. 4) and that the main electric power
switch installed prior to the machine is
disconnected “0” OFF.
-
An appropriately sized omnipolar circuit-breaker
with a minimum 3 mm gap between its contacts
must be installed between the power supply main
and the machine.
-
The manufacturer declines all responsibility for
accidents or damage to persons or property caused
by failure to comply with the above listed provisions.
•
Connect the electrical power cable (16) to the main
switch installed prior to the machine.
•
Connect the equipotential ground conductor to the
terminal (10).
Part 3:
For the technician and operator
3.1
DETERGENT DISPENSER (Fig. 7)
The machine is equipped with an automatic detergent
dispenser.
•
Insert the red supply tube (17) into the cannister
(18).
ATTENTION
Always wash the hands under running water if they come
into contact with detergent, or comply with the specific
indications pertaining to the utilized type of detergent.
•
Proceed with a few no-load cycles until the intake and
delivery tubes have filled.
To adjust the dispenser, refer to the relative enclosed
manual and to the utilized type of detergent.
3.2
FILLING THE RINSING AGENT DISPENSER
(Fig. 7)
•
Insert the transparent tube (19) into the cannister (20)
containing rinsing agent.(Refer to the specific
instructions given with the rinsing agent itself).
•
Start the machine as described in paragraph 3.3. The
dispenser will suck about 3 cm of liquid from the
cannister.
•
Fill during the cycle by opening (slightly) and closing
the door until the tube has completely filled.
3.2.a Adjusting the dose (Fig. 7)
•
Start the machine as described in paragraph 3.3 amd
hold a glass up to the light at the end of the cycle.
•
The drops of water on the glass will indicate insufficient
dosage while, the streaking or spotting will indicate,
instead, an excessive dosage.
•
Regulate by means of the plug (21), turning clockwise
to decrease the quantity or anticlockwise to increase it.
IMPORTANT
These data are indicative and not binding since they may
vary according to the hardness of the water or the utilized
type of detergent and rinsing agent.
ATTENTION
If the utilized product (detergent or rinsing agent) is
changed, it is advisable to flush out the dosing system with
water and to then proceed by filling the dispensers.
3.3
PREPARING THE MACHINE AND THE
WASHING OPERATIONS
3.3.a Preparing the machine (Fig. 8)
1. Turn on the main power switch prior to the machine.
2. Open the water supply cock.
3. Check that the cannister of detergent and rinsing agent
contain sufficient product for daily needs.
4. Turn the mains selector (1) and the lamp (2) lights. The
washing tub will immediately begin to fill. Once the
ENGLISH
Part 3:
For the technician and operator
Part 2:
For the qualified technician
