BLUE JAY BJ-S-W2S2-K2 User Manual Download Page 8 | Manualshive

Page: 8 / 11

BLUE JAY BJ-S-W2S2-K2 User Manual Download Page 8

Product Manual

Tel: +0086-023-86850812

Email:[email protected]

Fax:+0086-023-67636974

Add: Building 13, 2-8, Jialing third village Pioneer Park, Jiangbei District, Chongqing

5

5.- Operation mode

When the S series controller is powered up, all the LED indicator will on, and controller start

self- test to check the sensor status. After some seconds, the controller is ready for operation and
shows one of the available screens.

Notes:

If there is any sensor off line, the display will show “

“to indicate the sensor

failure.

Up key

. Press this key to increase values displayed on the display. Hold down this key to speed

up the incremental action.

Down key

. Press this key to decrease values displayed on the display. Hold down this key to

speed up the decrements.

Menu key

. Pressing the "Manu" key the can open the programming menu and return to previous

menu.

Enter key.

Pressing the “Enter” key, you exit it with saving any modification that you might have

done, in menu operation press “Enter” key; user can go to the next menu.

«
...
6
7
8
9
10
...
»

Summary of Contents for BJ-S-W2S2-K2












Reviews:

No comments