BLUE CHIP Magnum ETX User Manual Download Page 10

MAGNUM ETX 

  

 

 

Precautions 

Page | 10  

 

General Precautions 

Your  Single  Board  Computer  is  susceptible  to  damage  by  electrostatic  discharges.  In  order  to  avoid  damage, 
you  should  work  at  an  anti-static  bench  and  observe  normal  anti-static  precautions.  Wear  an  anti-static  wrist 
strap connected to an earth point 

before

 opening any packaging. 

 

Where  a  wrist  strap  is  not  available,  discharge  any  static  charge  you  may  have  built-up  by  touching  an  earth 
point. Avoid any further movement that could build up another static charge. Touch an earth point from time to 
time to avoid further build-up, and remove the items from their anti-static bags only when required 
 

PS/2 Devices 

It is important that PS/2 devices (mouse and keyboard) are not connected or disconnected with the unit powered 
on. Damage or data corruption may occur if this precaution is not observed.

 

 

Electro-Static Discharges 

If you are going to open up the unit, it is important to realise that the devices on the cards within this unit can be 
damaged  by  static  electricity.  Bear  in  mind  that  the  damage  caused  by  static  electricity  may  vary  from  total 
destruction  to  partial  damage,  which  may  not  be  immediately  obvious.  This  could  have  an  effect  on  the 
product's reliability and warranty. Before opening the chassis, ensure that you take necessary static precautions. 
Ideally you should work at an anti-static bench and wear an approved wrist strap or if that is not possible, touch 
a suitable ground to discharge any static build up before touching the electronics. This should be repeated if the 
handling continues for any length of time.  

 

If it is necessary to remove a board or electronic assembly, place it into an anti-static bag. This will prevent any 
static electricity build up damaging the board. Metallised bags are preferred. Do not use black anti-static bags 
for any item containing a battery because these tend to be conductive and will discharge the battery. 

 

On-Board Battery 

The MAGNUM ETX board has an on-board Lithium cell connected. Great care should be taken with this type 
of battery. If the battery is mistreated in any way there is a very real possibility of fire, explosion, and personal 
harm.  Under  NO  circumstances  should  it  be  short-circuited,  exposed  to  temperatures  in  excess  of  100°C  or 
burnt, immersed in water, recharged or disassembled. 

 

Expired batteries remain hazardous and must be disposed of in a safe manner, according to local regulations. 

 

Le panneau de processeur est équipé d’une batterie de lithium. Le grand soin devrait être pris avec ce type de 
batterie. Si la batterie est mistreated il y a de dans de toute façon un possibility très vrai du feu, d’expolosion et 
de  mal  personnel.  Dans  au  cunes  circonstances  il  est  sous  peu  circuité,  exposé  aux  températures  au  dessus  de 
100 degrés de centrigrade ou brûlé, immergé dans l’eau, rechargée ou dissassambled. 
 
Les batteries expirées restent dazaedous et doivent être reejetées d’une façon sûre, selon des règlements locaux. 

Summary of Contents for Magnum ETX




































Reviews: