background image

NOTE:  For your protection, please note that equipment in 

this shipment was carefully inspected and packaged by skilled 

personnel before leaving the factory.

Upon acceptance of this shipment, the transportation

company assumes full responsibility for its safe delivery.

IF SHIPMENT ARRIVES DAMAGED:

1.

VISIBLE LOSS OR DAMAGE:

 Be  certain  that  any 

visible  loss  or  damage  is  noted  on  the  freight  bill

or express receipt, and that the note of loss or damage 

is signed by the delivery person.

2.

FILE CLAIM FOR DAMAGE IMMEDIATELY: 

Regardless of the extent of the damage.

3.

CONCEALED LOSS OR DAMAGE:  if damage is 

unnoticed until the merchandise is unpacked, notify the

transportation company or carrier immediately, and 

file “CONCEALED DAMAGE” claim with them.  This         

must be done within fifteen (15) days from the date 

the delivery was made to you.  Be sure to retain the

container for inspection.

Bloomfield cannot assume liability for damage or loss 

incurred in transit.  We will, however, at your request, supply 

you with the necessary documents to support your claim.

WARRANTY STATEMENT

SERVICE POLICY AND PROCEDURE GUIDE

ADDITIONAL WARRANTY EXCLUSIONS

SHIPPING DAMAGE CLAIMS PROCEDURE

1.

Resetting of safety thermostats, circuit breakers, 

overload protectors, or fuse replacements.

2.

All problems due to operation at voltages other than 

specified on equipment nameplates - conversion to      

correct voltage must be the customer’s responsibility.

3.

All problems due to electrical connections not made in 

accordance  with  electrical  code  requirements  and

wiring diagrams supplied with the equipment.

4.     Replacement of items subject to normal wear, to 

include such items as knobs and light bulbs.  Normal 

maintenance functions including adjustment of 

thermostats, microswitches, and replacement of fuses 

and indicating lights are not covered under warranty.

5.     All problems due to inadequate water supply, such as  

fluctuating, or high or low water pressure.

6.

All problems due to mineral/calcium deposits, or

contamination from chlorides/chlorines. De-liming is    

considered a preventative maintenance function and is 

not covered by warranty.

All electrical equipment manufactured by BLOOMFIELD is 

warranted against defects in materials and workmanship 

for a period of 

(1 year labor, two year parts)

 from the date 

of original installation and is for the benefit of the original 

purchaser, except that:

a.   airpots carry a 30 day parts warranty only.

b. dispensers; i.e., tea and coffee carry a 90  days parts     

      warranty only, excludes decanters.

c. decanters are not covered by this warranty

THE FOREGOING OBLIGATION IS EXPRESSLY GIVEN 

IN LIEU OF ANY OTHER WARRANTIES, EXPRESSED 

OR IMPLIED,  INCLUDING  ANY IMPLIED WARRANTY OF 

MERCHANTABILITY OR FITNESS FOR A PARTICULAR 

PURPOSE, WHICH ARE HEREBY EXCLUDED.  
BLOOMFIELD, LLC SHALL NOT BE LIABLE FOR  

INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES 

OR LOSSES FROM ANY CAUSE WHATSOEVER.
This warranty is void if it is determined that upon inspection 

by an authorized service agency that the equipment has 

been modified, misused, misapplied, improperly installed, or     

damaged in transit or by fire, flood or act of God.

It also does not apply if the serial nameplate has been 

removed or unauthorized service personnel perform service.

The prices charged by Bloomfield for its products are based 

upon the limitations in this warranty.  Seller’s obligation under 

this warranty is limited to the repair of defects without charge 

by a Bloomfield Authorized Service Agency or one of its 

sub-agencies.  This service will be provided on customer’s 

premises for non-portable models.  Portable models (a device 

with a cord and plug ot a dispenser) must be taken or shipped 

to the closest authorized service agency, transportation 

charges prepaid, for services.

In addition to restrictions contained in this warranty, specific 

limitations are shown below (Additional Warranty Exclusions).  

Bloomfield Authorized Service Agencies are located in 

principal cities.
This warranty is valid in the United States, Canada and void 

elsewhere.  Please consult your classified telephone directory 

or your food service equipment dealer; or, for information and 

other details concerning warranty, write to:

Service Parts Department

Bloomfield

10 Sunnen Drive, St. Louis, MO 63143

  Phone:  (314) 678-6336...

Fax: (314) 781-2714

[email protected] / www.wellsbloomfield.com

  7.   Full use, care and manuals may or may not be sent with 

each unit, only a condensed version. Please visit our 

web site to download the full version.

  8.   Travel  mileage is limited to fifty (50) miles from an    

authorized service agency or one of its sub-service 

agencies.

  9.   All labor shall be performed during normal working hours.  

Overtime premium shall be charged to the customer.

10.   All genuine Bloomfield replacement parts are warranted  

for ninety (90) days from date of purchase on non- 

warranted equipment.

Any use of non-genuine

Bloomfield parts completely voids any warranty.

11.   Installation, labor and job checkouts are not considered 

warranty.

12. Charges incurred by delays, waiting time or operating 

restrictions  that  hinder the service technicians ability

to  perform services  are not covered by warranty.  

This includes institutional and correctional facilities.

xi

Summary of Contents for 9121

































Reviews: