background image

3

Installation

Delivery and Location

DELIVERY AND INSPECTION

All Blodgett ovens are shipped in containers to prevent 

damage. Upon delivery of your new oven: 
•  Inspect the shipping container for external damage. 

Any evidence of damage should be noted on the 

delivery receipt which must be signed by the driver.

•  Uncrate the oven and check for internal damage. 

Carriers will accept claims for concealed damage if 

notified within fifteen days of delivery and the ship

-

ping container is retained for inspection.

The Blodgett Oven Company cannot assume responsibil-

ity for loss or damage suffered in transit. The carrier as

-

sumed full responsibility for delivery in good order when 

the shipment was accepted. We are, however, prepared 

to assist you if filing a claim is necessary.

OVEN LOCATION

The well planned and proper placement of your oven will 

result in long term operator convenience and satisfactory 

performance. 
The following clearances must be maintained between 

the oven and any combustible or non-combustible con-

struction.

Zephaire-100-E

•  Oven body right side - 0” (0 cm)
•  Oven body left side - 0” (0 cm)
•  Oven body back - 0” (0 cm)
•  Single and stacked oven bottom - 4-1/2” (11.4 cm)

Zephaire-200-E

•  Oven body right side - 1/2” (1.3 cm)
•  Oven body left side - 1/2” (1.3 cm)
•  Oven body back - 1/2” (1.3 cm)
•  Single and stacked oven bottom - 1/2” (1.3 cm)

 Adequate clearances must be available for servicing.

•  Keep the oven area free and clear of all combus-

tibles such as paper, cardboard, and flammable 

liquids and solvents.

•  Do not place the oven on a curb base or seal to 

a wall. This will restrict the flow of air and prevent 

proper ventilation resulting in damage to the oven.

Before making any utility connections to this oven, check 

the  rating  plate  to  be  sure  the  oven  specifications  are 

compatible with the electrical services supplied for the 

oven.
1.  Pull out control panel. The rating plate attached to the 

inside of the control compartment.

•  Do not place strong sources of heat such as open 

flame ranges, griddles, or charbroilers near the 

oven.  If such an instance exists, it is highly recom-

mended to purchase a heat shield, available from 

Blodgett.

•  Note that if temperatures are too high, a safety shut-

down may occur.

•  Failure to comply may invalidate the oven warranty.

Summary of Contents for ZEPHAIRE-100-E



















Reviews: