BLODGETT
www.blodgett.com
44 Lakeside Avenue, Burlington, VT 05401 • Toll Free: (800) 331-5842 • Phone: (802) 860-3700 • Fax: (802) 864-0183
CB42E-10-10K
SHORT FORM SPECIFICATIONS
Provide Blodgett model CB42E-10-10K, two 10 gallon direct steam kettles on a 42” wide electric boiler base.
The kettles shall have a double wall interior to form a steam jacket around the lower 2/3 of the kettle. The bottom of the kettle shall be of hemispherical design for superior heat circula-
tion. Steam control valve mounted in leg. The tubular stainless steel mounting legs shall have the steam supply and condensate return pipes completely concealed within the leg meme-
bers. The sealed stainless steel tilt mechanism bearings shall permit the kettle to tilt forward 90° for complete emptying. A removeable operating handle with heat proof knob shall be
mounted on the left or right. Unit shall have a single support leg with nylon insert. Construction shall be all welded satin finish 304 stainless steel with a 316 stainless steel liner.
The boiler shall be 24 kW, 42” wide electric steam boiler cabinet. Polished stainless steel cabinet base shall be of modular design to match other Blodgett steam equipment. Unit shall
have 6” (152mm) stainless steel legs, adjustable bullet feet on front and adjustable flanged feet on rear, reinforced stainless steel counter top and hinged doors with magnetic latches. All
piping shall be confined within the cabinet. Unit shall be automatically filled with water and brought to pressure when power switch is turned on. Cold water condenser shall automatical-
ly condense exhausted steam in water before releasing it to drain. Boiler controls shall include automatic water level, pressure gauge, water gauge glass, pressure control with pressure
safety control, safety relief valve, cathodic protector and CSD-1 secondary low water cut off.
Unit shall have a hot and cold water faucet with control valves, 3" (76 mm) deep sinks with drain and splash guards.
Kettles and boiler shall be ASME code stamped and National Board registered. Provide options and accessories as indicated.
Printed in U.S.A.
NOTE:
FOR COMMERCIAL USE ONLY
NOTE:
The company reserves the right to make
substitutions of components without prior notice.
APPROVAL/STAMP
P/N S00095 Rev C (5/06)
WATER SUPPLY:
Water quality is a major factor affecting the performance of your steamer. If you are
unsure of water quality, consult a local water treatment specialist and have the water
analyzed. Your water supply must be within these general guidelines:
Total dissolved solids: Less than 60 PPM
Total alkalinity: Less than 20 PPM
Silica:
Less than 13 PPM
Chlorine:
Less than 1.5 PPM
pH Factor:
7.0 - 8.5
Water which fails to meet these standards should be treated by installation of a water
conditioner. Failure or malfunction of this steamer due to poor water quality is not cov-
ered under warranty.
WATER & DRAIN CONNECTIONS:
Drain
2” (51mm) IPS piped to open floor drain. No solid connection.
24” length before open air opening (no bends or elbows)
Cold Water
3/8” (10mm) tubing at 25-50 PSI (170-345 kPa)
Steam Take Off 3/4” IPS optional to operate adjacent equipment
SHIPPING INFORMATION:
Approx. Weight:
CB42E-10-10K
720 lbs. (327 kg)
ELECTRICAL CHARACTERISTICS
kW PH
AMPS PER LINE
208V 220V 240V 380V 415V 480V 600V
24
1 115.4 109.1 100
n/a
n/a
n/a
n/a
3
66.6
63
57.7 36.5 33.4 28.9 23.1
36
3
99.9 94.5 86.6 54.7 50.1 43.3 34.6
42
3 116.6 110.2 101
63.8 58.4 50.5 40.5
48
3
n/a
n/a 115.5 72.9 66.8 57.7 46.2
