manualshive.com logo in svg

Blodgett 100E-KLS, Installation Operation & Maintenance, Page: 7 / 24

Share
Download
Blodgett 100E-KLS Installation Operation & Maintenance Download Page 7

OM-KLS-E

       5

Inspection & Unpacking

CAUTION

THIS UNIT IS VERY HEAVY.  INSTALLER 

SHOULD OBTAIN HELP AS NEEDED TO LIFT 

THIS WEIGHT SAFELY.

The unit will arrive in a heavy shipping carton and will be banded to a skid. 

Immediately upon receipt, inspect the carton carefully for exterior damage.

Carefully cut any polyester straps around the carton and detach the sides of the box 

from the skid.  Pull the carton up off the unit.

Thoroughly inspect the unit for concealed damage.  Report any shipping damage or 

incorrect shipments to the delivery agent.

Write down the model number, serial number, and installation date, and retain this 

information for future reference.  Space for these entries is provided at the top of the 

Service Log at the back of this manual.  Keep this manual on file and available for 

operators to use.

When installation is to begin, carefully cut any straps which hold the unit on the skid. 

Lift the unit straight up off the skid. Examine packing materials to be sure that loose 

parts are not discarded with the materials.

CAUTION

SHIPPING STRAPS ARE UNDER TENSION 

AND CAN SNAP BACK WHEN CUT.  TAKE 

CARE TO AVOID PERSONAL INJURY OR 

DAMAGE TO THE UNIT BY STAPLES LEFT IN 

THE WALLS OF THE CARTON.

The unit will arrive in a heavy carton.

Inside it will be banded to a skid.

Summary of Contents for 100E-KLS

























Reviews:

No comments