background image

OM-KLS-E

       13

WARNING

KEEP WATER AND SOLUTIONS AWAY FROM 

CONTROLS AND ELECTRICAL EQUIPMENT.  

NEVER SPRAY THE SUPPORT HOUSING OR 

ELECTRICAL CONNECTIONS.

A. 

Suggested Tools:

 

1. 

 Cleaner, such as Klenzade HC-10 or HC-32 from ECOLAB, Inc.

 

2. 

 Kettle brushes in good condition (and a bottle brush, for the draw-off).

 

3. 

 Sanitizer such as Klenzade XY-12.

 

4. 

 Film remover such as Klenzade LC-30.

B. 

Precautions:

 

Before cleaning, shut off the kettle by turning the thermostat dial to “OFF”, and 

shut off all electric power to the unit at a remote switch, such as the circuit 

breaker.

C. 

Procedure: 

 

1. 

 Clean food-contact surfaces as soon as possible after use. If the unit is in 

continuous use, thoroughly clean and sanitize the interior and exterior at 

least once every 12 hours.

 

2. 

 Scrape and flush out food residues. Be careful not to scratch the kettle 

with metal implements.  Close the draw-off.

 

3. 

 Prepare a hot solution of the detergent/ cleaning compound as instructed 

by the supplier. Clean the unit thoroughly. A cloth moistened with 

cleaning solution can be used to clean controls, housings, and electrical 

conduits.

 

4. 

 Rinse the kettle thoroughly with hot water, then drain completely.

 

5. 

 Disassemble the tangent draw-off valve. Clean the draw-off port and 

each valve part with a brush.

 

6. 

 Rinse the kettle and draw-off valve parts thoroughly with hot water, then 

drain completely.

 

7. 

 As part of the daily cleaning program, clean soiled external and internal 

surfaces. Remember to check the sides of the unit and control housing.

 

8. 

To remove stuck materials, use a brush, sponge, cloth, plastic or rubber 

scraper, or plastic wool with the cleaning solution. To reduce effort 

required in washing, let the detergent solution sit in the kettle and soak 

into the residue. Do NOT use abrasive materials or metal tools that might 

scratch the surface. Scratches make the surface harder to clean and 

provide places for bacteria to grow.

 

 

 Do NOT use steel wool, which may leave particles in the surface and 

cause eventual corrosion and pitting.

 

CAUTION

MOST CLEANERS ARE HARMFUL TO 

THE SKIN, EYES, MUCOUS MEMBRANES 

AND CLOTHING.  PRECAUTIONS SHOULD 

BE TAKEN.  WEAR RUBBER GLOVES, 

GOGGLES OR FACE SHIELD AND 

PROTECTIVE CLOTHING.  CAREFULLY 

READ THE WARNINGS AND FOLLOW 

THE DIRECTIONS ON THE LABEL OF THE 

CLEANER TO BE USED.

Use only a sponge, cloth or plastic 

brush to clean the kettle.

Scrapers or steel wool can 

harm the kettle surface.

CAUTION

DO NOT MIX THE PARTS OF DIFFERENT 

DRAW-OFF ASSEMBLIES DURING 

WASHING.  THE PARTS ARE NOT ALWAYS 

INTERCHANGEABLE.

Cleaning

Summary of Contents for 100E-KLS

























Reviews: