Blizzard Lighting SnowBlind User Manual Download Page 8

Page 8

Snowblind User Manual Rev. C  

 

 

© 2021 Blizzard Lighting, LLC

USING THIS FIXTURE WITH THE wiCICLE® WIRELESS 

DMX SYSTEM

In addition to the unbridled thrill you already 

received the first time you plugged in your fix

-

ture, you’ll be delighted to know that This fix

-

ture also works seamlessly with our wiCICLE

®

 

Wireless DMX system, 

without additional power

.

• ONLY fixtures bearing this logo are certified for use with the wiCICLE

®

 

without external power.

• Unauthorized modification and/or using the wiCICLE

®

 with un

-

approved fixtures may cause damage to the wiCICLE

®

 or fixture.  

UNDER NO CIRCUMSTANCES IS BLIZZARD LIGHTING RESPON

-

SIBLE FOR ANY DAMAGE FROM SUCH OPERATION.

• Fixtures bearing the above logo 

MUST

 only use cable and connectors 

which separate chassis/case ground from cable shielding.  Cabling with 

the shield connected to the connector’s case/chassis may cause malfunc-

tion and damage to the wiCICLE

®

 or fixture.

• wiCICLE

®

 transmitters have additional power requirements and 

therefore cannot be powered directly from the fixture.  You will 

need to utilize the supplied AC/DC adaptor to drive wiCICLE

®

 

transmitters in your system.

WE HAD THIS SPACE, SO WE FIGURED WE’D DRAW 

YOU A PICTURE:

Antenna Housing & 1/2-wave 

Antenna

Antenna ferrule & articulation 

joint

Stainless Steel Housing

Recessed Selector Button
Status LED

3-Pin XLR Connector 

(Male on transmitter, Female 

on receiver model)

Summary of Contents for SnowBlind

















Reviews: