Blizzard Lighting Motif Atelier 16FX Manual Download Page 3

Page 3

Motif™ Atelier 16FX User Manual Rev. A  

 

 

Copyright © 2018 Blizzard Lighting, LLC

1. GETTING STARTED

What’s In The Box?

 

•  1 x Motif™ Atelier 16FX LED Fixture

•  An Ever-So-Handy Power Cord

•  DMX Signal Cable

•  This Lovely User Manual

Getting It Out Of The Box

 

Congratulations! You just purchased an awesome, most excellent linear LED wash 

fixture with 10-40° asymmetrical lighting distribution. Now that you’ve got your Motif™ 

Atelier (or hopefully, Ateliers!), you should carefully unpack the box and check the 

contents to ensure that all parts are present and in good condition. If anything looks as 

if it has been damaged in transit, notify the shipper immediately and keep the packing 

material for inspection. Again, please save the carton and all packing materials. If a fix

-

ture must be returned to the factory, it is important that the fixture be returned in the 

original factory box and packing.

Powering Up! 

All fixtures must be powered directly off a switched circuit and 

cannot be run off a 

rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer 

channel is used solely for a 0% to 100% switch

.  

AC Voltage Switch -

 Not all fixtures have a voltage select switch, so please verify that 

the fixture you receive is suitable for your local power supply.  See the label on the 

fixture or refer to the fixture’s specifications chart for more information.  A fixture’s 

listed current rating is its average current draw under normal conditions. Check the 

fixture or device carefully to make sure that if a voltage selection switch exists that it is 

set to the correct line voltage you will use.

 

Warning! 

Verify that the voltage select switch on your unit matches the line 

voltage applied. Damage to your fixture may result if the line voltage applied 

does not match the voltage indicated on the voltage selector switch. All 

fixtures must be connected to circuits with a suitable Ground (Earthing).

Getting A Hold Of Us

If something is wrong, please just visit our website at www.blizzardpro.com 

and open a support ticket. We’ll be happy to help, honest.

Disclaimer:

 The information and specifications contained in this document are subject 

to change without notice. Blizzard Lighting™ assumes no responsibility or liability 

for any errors or omissions that may appear in this user manual. Blizzard Lighting™ 

reserves the right to update the existing document or to create a new document to 

correct any errors or omissions at any time. You can download the latest version of this 

document from www.blizzardpro.com.

Author:

Date:

Last Edited:

Date:

J. Thomas

7/21/2018

J. Thomas

7/21/2018

Summary of Contents for Motif Atelier 16FX

























Reviews: