Page 10
Colorise™ Quadra Manual Rev. A
© 2015 Blizzard Lighting, LLC
Using the AnyFi™ Wireless DMX Receiver
In addition to the unbridled thrill you already received the first time you turned on your
fixture, you’ll be delighted to know that your Colorise™ Quadra is equipped to work
seamlessly with our own Skywire™ 2.4GHz wireless DMX products,
as well as W-DMX™ wireless products. W-DMX™ is a two-time
award winning wireless DMX technology, created and owned by
Wireless Solution Sweden AB.
Skywire™ wireless DMX products feature 512 auto-assigning
frequencies in 7 groups allowing up to 7 systems to run
simultaneously in the same space, completely free of interference,
with reliable wireless communication for over 1000 feet line-of-
sight! Using W-DMX™ wireless, you can expect an outstanding wireless range of up to 500
meters (line-of-sight), very easy setup, and leave any worries behind concerning loss of signal
due to its built-in FHSS technology (Frequency Hopping Spread Spectrum).
So first, if you would like to use Standard 2.4GHz wireless DMX, you will need a Blizzard
wiCICLE® transmitter, Lightcaster™ transceiver, or any Blizzard Lighting controller that has
this type of built-in wireless transmitter, like our Kontrol 6 Skywire™ to act as a transmitter.
And if you plan on using W-DMX™ 2.4GHz wireless for your setup, you will need a W-DMX™
transceiver to broadcast the signal from your controller, such as our Lightcaster W-DMX™.
Ready to move on? Well alrighty!
1.)
IMPORTANT
-
Set the Fixture to Receive Wireless Signal in the Control Panel
a.) Navigate the main menu to reach
SET,
press
<ENTER>,
then use the
<UP/
DOWN>
buttons until
SIGN
is displayed, then press
<ENTER>
again. Now use the
<UP/DOWN>
buttons to highlight
2.4G
(wireless mode), and press
<ENTER>
to
confirm.
2.) Resetting The Wireless
a.) Navigate the main menu to reach
SET
, press
<ENTER>
, then use the
<UP/
DOWN>
buttons until
WIRE
is displayed, then press
<ENTER>
again.
b.) From here, you can use the
<UP/DOWN>
buttons to highlight
REST
and press
<ENTER>
, select
YES
, then
<ENTER>
to reset the wireless setup.
3.) Select W-DMX™ or Standard 2.4GHz Receiver
a.) Make sure the device you are using to transmit signal with is powered on.
b.) Navigate the main menu to reach
SET
, press
<ENTER>
, then use the
<UP/
DOWN>
buttons until
WIRE
is displayed, then press
<ENTER>
again.
c.) Now use the
<UP/DOWN>
buttons to highlight
KEY
in the menu, and press
<ENTER>
.
d.) At this point, please note that every time you touch the
<ENTER>
button, the
wireless LED status indicator changes between 4 colors
(but only 2 are functional)
:
•
GREEN
:
W-DMX™ 2.4 GHz Mode
•
YELLOW
:
Standard 2.4 GHz Mode
(wiCICLE™ & LightCaster Compatible)
*Note:
RED
and
BLUE
currently have no function during this selection process.
e.) While the LED indicator is illuminated in
GREEN
(for W-DMX)
or
YELLOW
(for
Standard 2.4GHz)
, press and hold the
<ENTER>
button for
3 seconds
to make your
chosen wireless type the active wireless DMX signal type.
For W-DMX™ connections, you should be done. The fixture will detect the signal!
*For Standard 2.4GHz
connections, please continue to
Step 5
on the next page.
Universal Wireless DMX
