background image

 9

8

SECTION 3 – BLENDER OVERVIEW

 

Get to know your Blendtec Professional Series

3.1 

BLENDER JAR ASSEMBLY (see Figure 1)

• The 

lid

 is made from flexible rubber to seal liquids within the jar during blending�

• The 

clear vented cap insert

 allows heated air to escape and enables ingredients 

to be easily added�

• The 

jar

 is made from BPA-free Tritan™ copolyester to provide maximum strength 

and clear visibility�

• The 

blade assembly

 is stainless steel with a patented design to provide fast, 

consistent blending�

NOTE: Filling the blender jar beyond the marked capacity is not recommended�

3.2 

BLENDER MOTOR BASE (see Figure 2)

• The 

motor base cover

 encloses the motor base housing when it’s not 

installed in a counter-top�

•  The 

drive socket

 is where the jar couples with the motor to turn the 

blade assembly�

•  The 

touch pad

 consists of nine buttons that operate pre-programmed 

settings for selective blender control, including a pulse button and two 

speed-control buttons�

• The 

LCD information center

 indicates status as well as overload or over-

temperature conditions�

• The 

motor base housing

 contains the power unit in a surgical stainless steel 

casing� Never remove the housing� This will void the warranty�

• The 

power switch

 is located on the front of the motor base, at the bottom�

• The 

power cord

 is located at the bottom on the back of the motor base�

• The 

power unit 

is located within the blender motor and contains the machinery 

that runs the blender�

POWER SPECIFICATIONS

The Professional Series is made for 110/120 volts circuits only�

It is rated at 13 amps/1560 watts�

It is highly recommended that this unit be protected by a 15 amp circuit 

breaker or fuse� 

 

Blender Drive Socket

Touch Pad 

LCD Information Center

Power Unit

Motor Base Cover

FIGURE 2: MOTOR BASE

FIGURE 1: BLENDER JAR ASSEMBLY

Jar 

Lid

Blade Assembly

Clear Vented

Cap Insert

Motor Base 

Housing

Power Switch

Summary of Contents for Professional Series












Reviews: