background image

12 

 

TROUBLESHOOTING 

 

You can solve many common problems easily, saving you the cost of a possible service call. Try the 

suggestions below to see if you can solve the problem before calling the servicer.  

 

Troubleshooting Guide  

 

 

 

 

PROBLEM

 

POSSIBLE CAUSE

 

REMEDY

 

 

Appliance 

does not 

operate. 

 

Appliance is not connected to a power 

supply. 

 

The appliance is turned off. 

 

Tripped circuit breaker or a blown fuse. 

 

Connect the appliance. 

 

 

Switch on the appliance 

 

Switch on circuit breaker or replace 

fuse. 

 

 

 

 

Appliance is 

not cold 

enough. 

 

The temperature is not set correctly. The 

ambient temperature could require a 

lower temperature  setting. 

 

The door was  opened too often. 

 

 

The door was not closed completely. 

Door is not hermetically  sealed. 

 

 

The condenser is too dirty. 

 

The ventilation opening is blocked or too 

dusty. 

 

Check the set temperature. 

Set a lower temperature 

 

 

Do not open the door more often than 

necessary. 

 

Close door properly. 

 

Check the door seal and clean or 

replace. 

 

Clean the condenser when necessary. 

 

Clear the obstructions and clean the 

dust. 

 

 

 

 

Appliance 

turns itself on 

and off 

frequently. 

 

The room temperature is higher than 

average 

 

A large amount of food has been added 

to the unit. 

 

 

The door is open too often. 

 

 

The door is not closed completely. 

 

The door gasket does not seal properly. 

 

Put the appliance in a cooler place. 

 

 

Leave the appliance to work for a 

while until the set temperature has 

been reached. 

 

Do not open the door more often than 

necessary. 

 

Close door properly. 

 

Check the door seal and clean or 

replace. 

 

 

The light does 

not work. 

 

Appliance is not connected to a power 

supply. 

 

Tripped circuit breaker or a blown fuse. 

 

The light was switched off on the control 

panel. 

 

Connect the appliance. 

 

 

Switch on circuit breaker or replace 

fuse 

 

Switch on the light. 

 

Vibrations 

 

The appliance is not properly leveled. 

 

Level the appliance with the 

adjustable feet. 

 

 

The appliance 

seems to 

make  too 

much  noise. 

 

The rattling noise may come from the flow of the refrigerant, which is normal. As each 

cycle ends, you may hear gurgling sounds caused by the flow of refrigerant in your 

appliance 

 

If temperature fluctuations occur, the contraction and expansion of the inner walls may 

cause popping and cracking noises. 

 

The appliance is not properly level. 

 

Level the appliance with the 

adjustable feet. 

 

 

The door will 

not close 

properly. 

 

The appliance is not properly level. 

 

 

The door was reversed and not properly 

installed. 

 

The gasket is dirty. 

 

The shelves are out of position. 

 

Level the appliance with the 

adjustable feet. 

 

Check the door hinge and reassemble 

correctly. 

 

Clean the door gasket. 

 

Check the shelves and refit correctly, 

 

 

Summary of Contents for BLZ-SSRF-DBDR5.1














Reviews: