background image

 

Version 

1.02 

   Page 

12   Printed: 

November 

7, 

2012 

OM-BRII/90.PUB 

Installation—Location & Clearances

 

YOUR STOVE'S LOCATION  

 
1.  Your stove should be centrally located in the area to be heated. It should be placed away from 

doors and hallways and out of the line of traffic as much as possible. Plan ahead to be certain that 
furniture, drapes and curtains cannot come within the combustible clearances listed on the table 
below.  

2.  This stove must be connected to a chimney that is vented to the outside. Never permit your stove to 

vent into any room of the building.  

3.  Check the attic or space above the ceiling, or behind walls through which you intend to run your 

stove pipe and chimney,  to assure there are no existing heating ducts, electrical wiring, conduit, or 
major structural support beams in the way. A straight stove pipe is best.  

4.  Consult illustrations in the back of this manual to ensure that you install your stove the proper 

minimum distances from combustible materials.  

 

FLOOR PROTECTION 

 

Floor protection may be any non-combustible material or Listed Floor Protector.  In the USA It must 
extend at least 18” in front of the loading door opening and 8 inches beyond the sides of the door 
opening. In Canada 18” in front  and 8 inches beyond the side and inline with the rear of the stove.  In 
certain installations floor protection must be provided under the chimney connector and 2 inches 
beyond each side of the chimney connector.  Position the floor protector so that no floor ducts are 
covered.  
 

CLEARANCES TO COMBUSTIBLE MATERIALS 

** Mobile Home and Alcove Installations must use double wall listed pipe, side shields and rear shield. 
Mobile Home Installations require Outside Combustion Air Kit # Z1526.

 

 

Residential Installations 

 

Single Wall Pipe (24 MSG Black) 

15” / 381 mm 

15” / 381 mm  25.75” / 654 mm  18” / 457 mm  15” / 381 mm 

Listed Double Wall Pipe—Close Clearances 

Use side shields and  rear shield. 

(Must use for Mobile / Manufactured 
Home Installations, Alcove Installation 
and Close Clearance Installations)

 

14” / 356 mm 

8” / 203 mm  24.75” / 629 mm  11” / 279 mm 

8” / 203 mm 

Summary of Contents for BRIARWOD BRII/90



















Reviews: