manualshive.com logo in svg

Blaze King 6003T, Installation And Operating Instruction Manual

Share
Download
Blaze King 6003T Installation And Operating Instruction Manual Download Page 16

The Tuscany 

by Blaze King

   

 

 

 

Owners Installation and Operation Manual 

OM-6003T 

Page 16 

DATE PRINTED: 4/3/14 
Version 1.10 SIT 

Vent Restrictors 

Due to the extra flow 
produced by certain 
venting configurations 
vent restrictors must be 
placed in the vent to 
maintain performance. 
The vent restrictors 
come in four sizes. 
When your installation 
r e q u i r e s   a   v e n t 
restrictor the correct 
restrictor is placed 
inside the vent adaptor 
collar on the unit. 
Proper instructions for 
installing a vent 
restrictor are included 
in the vent restrictor kit. 

4” Collar attached 

Adaptor 

Before sliding the pipe into the termination ensure that you 
slide the decorative wall thimble cover and penetration heat 
shield over the pipe. 

 

Slide the pipe into the vent, making sure there is at least 1” 
overlap between the pipe and the terminal. Attach the pipe by 
attaching two sheet metal screws through the termination 
straps and into the pipe. Bend back the straps towards the 
termination cap making sure they are hidden by the 
decorative thimble. Finally attach the wall penetration heat 
shield and secure with wood screws.   

HOT

Vertical Installations 

Always maintain the 1” clearance around the vent pipe 
(vertical), when passing through ceilings, walls, roofs, 
enclosures, attic rafters or any combustible surfaces. 
DO NOT PACK AIR SPACES WITH INSULATION. 
Refer to the vent chart for maximum allowable vertical and 
horizontal installations. 
When planning your installation determine if ceiling joists, roof 
rafters or other framing will obstruct the vent system. You may 
have to use 45° elbows to navigate around any obstacles. 
When passing through a flat ceiling install a Box/Wall thimble. 
Cut a 10” square hole and frame as shown in the diagram 
opposite. 
Ensure all pipe sections are fully twist locked. 

Basement Installations 

To achieve the minimum vertical rise a 36” snorkel may be used. 

Where the bottom of the terminal may be blocked by snow etc 

ensure provision is made for adequate drainage. 

Drainage 

Minimum 12” 

NOTE: ALWAYS CHECK YOUR LOCAL CODES 
BEFORE INSTALLING VENTING. NECESSARY 
CLEARANCES AND REQUIRMENTS MAY VARY 
FROM STATE TO STATE(PROVINCE TO 
PROVINCE).  

Installation Instructions 

Restrictor Sizes 

Summary of Contents for 6003T







































Reviews:

No comments

Brands by name

Popular brands

Load more brands