background image

Voltage Supply

Integrated Fuse

The integrated fuse in the device protects the output 
voltage and the entire electrical system in case of 
malfunction. Do not replace damaged fuse with higher 
current.

Switching On/Off

This device will automatically turn on if a music signal is 
detected. The device will also automatically turn off if no 
music signal is received.

Remote Control

Recycling and Disposal

 

Please dispose responsibly.

 

Subject to change.

Disconnect the negative terminal of the battery. 
Refer to the safety notes of vehicle manufacturer.
Ensure positions of the holes are nowhere near the 
vehicle component to avoid any damage during 
drilling.
Ensure cross section of the cable is no less than 
2.5mm2 if the positive and negative cables are too 
long.
Incorrect installation may result in malfunction of 
the device or the car sound system.

The amplifier is designed to use 4-8 AWG power and 
ground cable.
Select a dry and well-ventilated location
to install the device.
The device must not be installed in overly
exposed location such on the rear shelf,
rear seat etc.
The installation location must be suitable for
screw holes and have stable ground support.
Ensure to connect the ground wire of the unit 
properly the vehicle chassis.
Ensure to use leads that is larger than 10-gauge 
(AWG 10) when connecting to +12V and GND 
terminals.
Connect the +12V power input lead only when the 
rest of the connections has been properly set. 

In no event shall Blaupunkt be liable for any direct, 
indirect, punitive, incidental, special consequential 
damages, to property or life, improper storage, 
whatsoever arising out of or connected with the use 
or misuse of our products.
USA & CANADA : Product not intended for sale in 
the United States and Canada. If purchased in the 
U.S. or Canada, this product is purchased as-is. No 
warranty, express or implied is provided in the U.S. 
and Canada.

CAUTIONS

Proper system planning is vital in order to maximize the 
device’s performance and road safety. Plan your 
installation carefully to avoid compromising 
performance reliability of the system. Consult an 
authorized Blaupunkt dealer for installation or 
reparation. Read the manual carefully before operating 
the device for the first time.

Safety Notes

Ensure to follow below safety notes during
installation and wiring connection : -

Installation and Connection Instructions

Disclaimer

Use the supplied power extension cable to connect 
to the positive battery terminal.
Firmly and carefully connect the ground lead to a 
bare metal point on the vehicle chassis.
The control of the device should be a two-channel 
control, either via the preamplifier outputs or the 
loudspeaker, output of the car sound system.
A control solely via the right or left channel is also 
possible since the low-frequency portion of the 
music is generally identical on both channels.

1

Summary of Contents for MPA 11500













Reviews: