manualshive.com logo in svg

BLAUBERG KOMFORT EC DW Series, Operation Manual

Share
Download
BLAUBERG KOMFORT EC DW Series Operation Manual Download Page 15

www.blaubergventilatoren.de

15

KOMFORT EC DW

1

3

2

4

The unit is supplied with an outdoor temperature sensor. 

The outdoor temperature sensor mounting is as follows, Fig. 18: 

1. Remove two screws that retain the sensor cover. 

2. Take off the sensor cover. 

3. Install the sensor on the outer wall. The installation place must not be 

subjected to direct solar light. 

4. Install the sensor cover back. 

5. Connect the sensor to the X1 terminal block in compliance with the 

electric wiring diagram, Fig. 14 and Fig. 16.

OUTDOOR TEMPERATURE SENSOR MOUNTING AND CONNECTION 

Fig. 18. Outdoor temperature sensor mounting and connection

Fig. 19. Duct humidity  sensor mounting

The FS1 duct humidity sensor is a specially ordered accessory. Connect 

the contact socket of the humidity sensor to the contact socket located 

inside of the heat recovery unit (ref. Fig. 19). After that fix the sensor using the 

clamp and the holder in the air duct upstream of the heat exchanger.

1.

2.

3.

DUCT HUMIDITY SENSOR MOUNTING AND CONNECTION

Duct humidity sensor installation 

place

Duct humidity sensor installation 

place

KOMFORT EC DW600-2 / KOMFORT EC DW 1000-4

KOMFORT EC DW2000-2 / KOMFORT EC DW 3800-2

KOMFORT EC DW v1(6)_EN.indd   15

10.08.2015   10:11:07

Summary of Contents for KOMFORT EC DW Series

































Reviews:

No comments

Brands by name

Popular brands

Load more brands