BLAUBERG Komfort EC D5B180 S14 Installation Manual Download Page 5

The condensate drainage system is designed for normal operation in premises with air temperatures above 0 °C! If the expected ambient
air temperatures are below 0 °C, the condensate drainage system must be equipped with heat insulation and pre-heating facilities.
Condensate drainage is not required for the Komfort EC D5B180-E modification. 

CONNECTION TO POWER MAINS

The air-handling unit is rated for connection to single-phase AC 120V/60 Hz power mains.  The unit must be connected to power mains using 
durable, insulated and heat-resistant conductors (cables and wires) with minimum cross section not less than 20 AWG.
The external power input must be equipped with an automatic circuit breaker built into the stationary wiring to open the circuit in the event 
of overload or short-circuit.  The position of the external automatic circuit breaker must ensure free access for quick power-off of the unit.  The 
circuit breaker trip current must correspond to the unit current consumption, refer to the Technical data section.
Connect the cables to the control unit using the electric lead-ins on the side of the unit. 
Make the electric connections through the terminal block, located in the control unit, in compliance with the External wiring diagram.

Access to the control unit 

External control units wiring diagram

2

3

4

14

13

12

11

10

9

8

7

6

5

15

L

1

External device 
NO (CO

2

 sensor)

PK fire alarm panel

(remove the jumper while 

connecting the contact)

120 V/ 60 Hz 

Control panel

- Tx Rx +

GND Tx

Rx +U

3

2

1

GND

+U

0-10V

GND

+U 0-10V

N

PE

РК

C

X1

16

SM-L

17

SM-N

Humidity 

sensor 

W

hit

e

Bro

wn

Gr

een

Yello

w

XP

QF

Electric actuators

 of the external air dampers

SM1

supply

L1      N

SM2

exhaust

L1      N

Designation

Name

Model

Wire**

N.o

External control unit contacts

LF230

2 x 20 AWG

SМ1*

Supply air damper actuator

LF230

2 x 20 AWG

SМ2 *

Exhaust air damper actuator

LF230

2 x 20 AWG

РК*

Contact from fire alarm panel

NO

2 x 20 AWG

* Is not included in the delivery set.
** Maximum connecting cable length is 65 ft!

www.blauberg.us

MUI_82_Komfot_(EC)_D5B180_EN-01

174 N. 36th Street, Lafayette, IN 47905
e-mail: [email protected]

5

Summary of Contents for Komfort EC D5B180 S14






Reviews: