manualshive.com logo in svg

Blagdon Pump 25 Series, Service And Operating Manual, Page: 14 / 16

Share
Download
Blagdon Pump 25 Series Service And Operating Manual Download Page 14

HG-CF-1101 Rev. C – 19.05.06 

Page 14 

Wet Side Kit Structure 

TYPICAL CODE = 

SA  25 00  N  N  M  R 

PUMP BODY / BALL VALVE MATERIAL :

 

M : METALLIC                
N : NON-METALLIC 
S : 1/2” STAINLESS STEEL       
W : WEIGHTED VALVE BALL 
Z :  HYGIENIC MODELS 

VALVE BALLS :

 

B : BUNA-N                       S : 316 ST. STEEL     
D : DELRIN (ACETAL)       T : PTFE 
E : EPDM                          V : VITON 
N : NEOPRENE                  

PART NUMBER :-  

SA : ALL KITS 

DIAPHRAGMS :

 

B : BUNA-N                     P : POLYURETHANE 
E : EPDM                         R : SANTOPRENE       
H : POLYESTER             T : PTFE 
N : NEOPRENE               V : VITON 
O : ONE PIECE PTFE     X : HIGH TEMP.           

VALVE SEAT MATERIAL / 2:1 OPTION :

 

R : RUBBER OPTIONS 
(ONLY USED IF PUMP TRIMMED WITH 
RUBBER SEATS) 
1 : HIGH PRESSURE (W1 MODELS)      
 

MODEL NUMBER :

 

Pump Type i.e:-  06, 15 , 1H ,  1A ,  25 , 
40, 1B , 2B , 50 , 1C. 

Diaphragm Pump Wet-Side Kits - Part Number Structure 

 
The format of the Wet-Side kit part number is broken down as shown below. The number always starts with ‘SA’ followed by the model 
number, diaphragm letter, ball valve letter and pump material. If rubber seats are used, an ‘R’ is added to the end. A ‘W’ is added fol-
lowing the ball valve letter if pump is fitted with weighted balls. These are not available for sizes below 1”. 
 
If pump model number includes a revision number then this is added where shown below. Please refer to either the pump nameplate 
or the operating manual provided with the pump if this is to be included, i.e.  B0601SSBBTTS 
NOTE! This part number system does not apply to pumps designated :- 
B4001, B5001 or B7501. Please consult the pump Service & Operating Manuals for Wet-Side Kit numbers for these models. 
If in doubt please consult Sales at Blagdon Pump. 

DESIGN REVISION :  

SEQUENTIAL NUMBER STARTING AT 00 
(NOT USED IF MODEL HAS NOT BEEN 
REDESIGNED SINCE DEC. 1999) 
I.E. SA15BBNR 

(SEE NOTE ABOVE) 

Spares Kits 

The following details refer to the main recommended spares kits available for your Blagdon Pump. Not all combinations and trim 
options are listed here. Please refer to your local stockist / distributor if you require further details or availability of other kits. 

 
 

 

 - 

Air Side Kits 

-     SA10515 - Standard Air side kit. All pumps are Lube Free as standard. If lubrication is used inadvertently this will not 

                                       damage the pump in any way. 
                                       Note! This kit is identical to SA10415 but without the 8 G339 O-Rings. 
         
                                       
 

 - 

Valve Block Sub-Assemblies 

- 

                                       SA10463 - BSP 
                                       SA10465 - NPT 
                                       
 

 

- 

Wet Side Kits

 -    SA2500TTN                                                                                                                                     

                                                                             
                                       
 

 

- 

Filter / Regulator

 SA10444 

 

 

- 

Filter/Regulator/Lubricator - FRL

            SA10378                         

Summary of Contents for 25 Series

















Reviews:

No comments