EN
* Old versions of the DX4e and DX5e (with 2-position channel 5 switches) are
not
recommended for the 350 QX. Only
Smart Mode
and
Stability Mode
will
be available with GPS On.
Powering On
1. Power ON the transmitter.
2. Set the Rate Switch to Hi.
3. Set the Channel 5 Switch to 0 for Smart Mode.
4. Fully lower the throttle stick.
5. Place the 350 QX on a level surface outside with the status LED towards you.
6. Power ON the 350 QX.
7. Step back approximately16 feet (5 meters).
8. Ensure the status LED is solid green, indicating GPS lock.
9. Move the rudder stick full left, then full right, then back to center, setting the Home position and starting the motors.
10. Increase the throttle stick to begin fl ying.
Transmitter
Model
Type
Reverse
Setup
Throttle
Cut Setup
Mode Setup
Switch Positions
Throttle Cut
Return Home
Dual Rate
Switch
High
Rate
Low
Rate
DX4e (New)*
w/3-position
switch
N/A
N/A
N/A
N/A
Position 0 =
SMART Mode
Lower throttle
trim until motors
stop turning
Press and Hold
TRAINER/BIND
Release to EXIT
Rate
100%
fi xed
70%
fi xed
Position 1 =
AP Mode
Position 2 =
Stability Mode
DX5e (New)*
w/3-position
switch
N/A
N/A
N/A
N/A
Position 0 =
SMART Mode
Lower throttle
trim until motors
stop turning
Press and Hold
TRAINER/BIND
Release to EXIT
Rate
100%
fi xed
70%
fi xed
Position 1 =
AP Mode
Position 2 =
Stability Mode
DX6i
Acro
THRO-N
ELEV-N
GEAR-R
AILE-N
RUDD-N
FLAP-N
ACT
Travel Adj: GEAR POS (0) GEAR:
↑
100%;
GEAR/F MODE POS (1) GEAR:
↓
40%
FLAPS: Norm
←↑
100; LAND
↓
100
MIX 1: ACT; GEAR
→
GEAR
ACT
RATE D
0%; U + 100%
SW MIX
TRIM INH
SUB TRIM
THRO
↑
15-20%
GEAR 0; Mix 0 =
SMART Mode
Press throttle cut
FLAP Position 0
= OFF
FLAP Position 1 =
Return Home
ELEV-AIL D/R
100%
70%
GEAR 1; Mix 0 =
AP Mode
GEAR 1; Mix 1 =
Stability Mode
DX7/7SE
Acro
FLAP-R (6)
Others-N
N/A
Travel Adj: GEAR (0)
↑
100%;
GEAR (1)
↓
40%
MIX 1: FLAP
→
Gear OFF/ON
RATE
→
-50%
0%
SW: MIX
OFFSET: 0
GEAR (0);
Mix (0) =
SMART Mode
Lower throttle
trim until motors
stop turning
FLAP Pos 0
= OFF
FLAP Pos 1
= Return Home
ELEV-AIL D/R
100%
70%
GEAR (1);
Mix (0) =
AP Mode
GEAR (1);
Mix (1) =
Stability Mode
DX7S
Acro
AUX1-R
Others-N
Set To:
Trainer
Switch Select:
Move Gear to F MODE (F MODE:GEAR)
Leave FLAPS as AUX1
Set All Others to INH
MIX 1: GER > GER
RATE: 0%
-100%
OFFSET: 0%; TRIM: INH; SW: Mix0
F MODE (0) =
SMART Mode
Press
Trainer
FLAP Pos 0 = OFF
FLAP Pos 2 =
Return Home
ELEV-AIL D/R
100%
70%
F MODE (1) =
AP Mode
F MODE (1);
HOLD (1) =
Stability Mode
DX8
Acro
AUX1-R
Others-N
Set To:
Trainer
Switch Select: F-Mode to Gear;
Flap to Aux 1
All Others to INH
F MODE (0) =
SMART Mode
Press Trainer/
Bind
FLAP Pos 0
= OFF
FLAP Pos 2
= Return Home
ELEV-AIL D/R
100%
70%
F MODE (1) =
AP Mode
F MODE (2) =
Stability Mode
DX9/DX18
Acro
AUX1-R
AUX3-R
Others-N
Set To:
I (BIND)
Channel Assign: NEXT
1-4: N/A
5 Gear: B
6 AUX1: D
7 AUX2: RKnb
8 AUX3: H
9+: INH
B (0) =
SMART Mode
Press I (BIND)
D (FLAP) Pos 0
= OFF
D (FLAP) Pos 2 =
Return Home
ELEV-AIL D/R
100%
70%
B (1) =
AP Mode
B (2) =
Stability Mode
Transmitter Setup (BNF)
CAUTION:
When using a Futaba transmitter with a Spektrum DSM module, you must reverse the throttle channel and rebind. Refer to your Spektrum module manu-
al for binding and failsafe instructions. Refer to your Futaba transmitter manual for instructions on reversing the throttle channel.
Binding (BNF)
1. With the transmitter and quadcopter powered OFF, connect the battery to the 350 QX.
2. With the 350 QX on a level surface, turn ON the power switch and allow the quadcopter to initialize.
3. Wait until the blue LED on the quadcopter fl ashes rapidly, signaling the quadcopter is initialized and ready to bind.
4. Ensure throttle is in the low position, throttle trim is at neutral and the Flight Mode Switch is set to SMART Mode.
5. Press/pull the bind button/switch and power ON the transmitter.
6. Release the bind button/switch when the LED turns solid green.
