1
4
5
CCStudio
Setup
Blackhawk
123 Gaither Drive, Mt. Laurel, NJ 08054-1701
www.blackhawk-dsp.com
Blackhawk is a registered trademark of EWA Technologies, Inc.
USB510W-QSe-01
ETHERNET DEBUG INSTALL
This ETHERNET debug installation portion of the
USB510W
Quick Start Guide
series is intended to show how to configure the
USB510W
Emulator for operation
with Code Composer Studio using its LAN port.
For emulator debugging via the USB interface, please refer to USB Debugging Quick
Start Guide also included with the
USB510W
JTAG Emulator.
Inventory of Items Included
1. Blackhawk USB510W JTAG
Emulator POD
(
USB510W
) and 8 inch JTAG cable.
2. High-Speed USB 2.0 Compliant Cable
3. 5 Volt USB power supply
4. 20e_cTI-14t_TI Pin Converter
5. 20e_cTI-20t_ARM Pin Converter
6. Installation
CD
7. Warranty
Card.
8. Quick Start Guide.
Other Items Required
1. Target Board System—a self-powered
board with a TI DSP and compatible JTAG
header connection conforming to IEEE
1149.1 Standard.
2. Copy of Code Composer Studio Version
3.3
†
or later.
(Recommended CCSv4/5)
Installation Requirements
•
PC or Notebook computer with one free USB v1.1 or v2.0 port for USB debug or
USB510W
administration and/or free Ethernet port for LAN debug
†
.
•
Windows® 2000 or XP/Vista/Linux Operating System
•
Texas Instruments Code Composer Studio Version 3.3 or later.
•
CD-ROM Drive.
†
Ethernet connections to a local area network from the
USB510W
Ethernet port is made using a standard RJ45
patch cable (supplied). For direct connection (PC to
USB510W
) an RJ45 cross-over cable is required (not sup-
plied).
USB510W
administration of TCP/IP address and subnet mask is done via USB port on the emulator.
6
Quick Diagnostic
The
USB510W
is a network device, so when it is powered and connected to your network, you can use the
standard Windows PING command to test if the emulator is accessible from your PC. Just enter the command
shown below, which uses the default address. Your
USB510W
may be configured with a different address, so
check with your network administrator if you did not originally configure the device.
C:\>ping 10.0.9.1
QUICK
START
GUIDE
Blackhawk™
USB510W
JTAG
Emulator
(
USB510W
)
This equipment is designed to be
operated under the following envi-
ronmental conditions:
Temperature between 0°C –55°C.
Relative Humidity of 20% - 70%
non-condensing.
Operation of the unit outside of the
above range may affect structual
and mechanical integrity and
cause permanent damage.
Caution is necessasry to minimize
ESD (Electro-stactic Discharge)
which can damage electronic
components. Use in a controlled
environment where ESD materials
and practices are employed is
highly recommended.
I
MPORTANT
E
NVIRONMENTAL
C
ONSIDERATIONS
CCStudio v4 and later
1. In the CCS v4 or v5 bring up the
New Target Configuration
Win-
dow from the File Menu option.
2. From the connection drop down list select the
Blackhawk USB510W
Emulator
3. Select your board or device that is connected to the emulator.
4. Choose the Advance properties tab.
5.
Select “WiFi” in the
Connection Type
drop down.
6.
Enter the Emulator’s IP address
10.0.9.1
, if not already entered
.
7. Save this setting and launch the TI Debugger.
FIGURE 5 - USB510W Target Setup and Selection
CCStudio v3.3 Service Release 12
1. Launch Setup Code Composer Studio v3.3.
2. From the platform drop down list select the
bh-usb510(w) emulator
.
3. From the family drop down list select your target device family .
4. Select your board or device from the middle pane and double click on it.
5.
Right Click on the USB510W configuration and Choose Properties...
6. Go to Connection Properties Tab in the new dialog menu.
7.
Select “WiFi” in the
Connection Type
drop down.
8.
Enter the Emulator’s IP address
10.0.9.1
, if not already entered
.
9. Save & Quick the setting to launch Code Composer.
