background image

IMPORTANT:  Read

 

and understand all of the 

instructions and safety information in this manual 
before operating or servicing this tool. 

 

1.0

GENERAL INFORMATION

SAFETY RULES

1.1

1.

 BE FAMILIAR WITH YOUR TOOL.

Read the instruction manual. Become aware of its proper 
usage as well as the potential hazards.

2. 

KEEP WORK AREA CLEAN AND WELL LIGHTED.

Poor lighting and cluttered areas invite accidents.

3. 

USE SAFETY GLASSES.

4. 

MAINTAIN TOOL WITH CARE.

Keep tool in good condition at all times. Keep it clean for 
best and safest performance.

5. 

DON'T OVER-REACH.

Keep proper footing and balance at all times.

6. 

NEVER ATTEMPT TO MAKE A COMPRESSION ON A 
"HOT" LINE.

Never assume the power is OFF! Determine beforehand if 
any electrical hazards could exist when making a 
connection to a line or wire.

7. 

KEEP FINGERS AND OTHER BODY PARTS AWAY 
FROM COMPRESSION DIES & MOVING PARTS.

WARNING

Tools are 

NOT

 insulated for use on or near 

energized conductors. Use of these tools 
near energized conductors may lead to 
electrical shock, causing severe injury or 
death. 

DO NOT

 use these tools near 

energized conductors without adequately 
insulating operator and surroundings.

WARNING

Pinch point hazard. Compression Dies at high 
force can cause severe personal injury. Keep 
all body parts away from moving parts of the 
tool during operation.

FEATURES

1.2

 Fully automatic, self-contained power tool.

 Removable battery cartridge - simply change the 

cartridge for continuous use.

 One handed operation - control ram advancement 

and retraction with one hand.

 Protective rubber boot on “C” Head.

SPECIFICATIONS

HYDRAULIC COMPRESSION TOOL:

TBM12PCR-LI

Drive Unit: 

14.4V DC Motor

Dimensions:

 

16.5”L x 3.3”W x 12.6”H

Weight:

 

16.8 lbs. with battery

Capacities:

 

750 kcmil CU or Aluminum

Jaw Opening:

  1.65”

BATTERY:

144-BAT-LI

Battery Type: 

Sealed Lithium Ion

Voltage:

 

14.4V DC

Dimensions:

 

4.2”L x 3.3W x 2.6H

Capacities:

 

3.0Ah

Weight:

 

1.2 lbs.

Charging time:

  25 min. 80% Capacity

 

45 min. 100% Capacity

CHARGER:

144-CHR-LI

Input Voltage: 

120 - 240 V AC Single Phase

Dimensions:

  9”L x 5.7W x 3.2H

Weight:

 

3.5 lbs.

1.3

TA04694  B   Page 2 of 8

Summary of Contents for TBM12PCR-LI









Reviews: