Black Widow 1R / 2-BUTTON SERIES User Manual Download Page 6

6

Complete Default Reset

Following this procedure will set all

programmable features to factory default

settings.

1. Enter System Programming.
2 .Press Transmitter Buttons 1&2 together.

• The siren will chirp 6 times indicating the

reset signal was received.

• All programmable features are now set to

factory default settings.

2. Turn ignition off.

Programmable Features

1. Arming Mode. Select between manual

arming (Active), automatic arming (Passive), and

automatic arming with chirps that countdown

every 2 seconds until armed.
2. Passive Locking. Selects whether or not the

system will automatically lock the doors with

Passive Arming.
3. Ignition Locking. Automatically locks and

unlocks the doors with the ignition.The system

will not lock the doors if any door is open

when the ignition is turned on.
4. Arming Chirps. Select Normal or Silent

Arming.

5. Siren / Horn Chirps. When set for Horn

Chirps the horn will honk when the alarm is

armed, disarmed, and triggered, allowing the

siren to NOT be installed. Buttons 1&2

together add horn chirps with the warn away

feature.
6. Anti-Carjack Activation. Enables or disables

the anti-carjacking feature.
7. Anti-Carjack Mode. Selects one of three

Anti-Carjacking modes: Active, Passive, or Full-

Time. Anti-Carjack Activation must be enabled

for any Anti-Carjack mode to operate.

Active

. Pressing transmitter buttons 1&2 with

the ignition on will manually activate the Anti-

Carjacking feature.

Passive

. When selected, the Anti-Carjacking

feature will activate whenever a door is opened

while the ignition is on.

Full-time

. When selected, the Anti-Carjacking

feature will automatically activate each time the

ignition is turned on.
8. Two Stage Disarm. When selected, pressing

the button to disarm the system during a

trigger cycle will instead reset the siren and

leave the alarm armed. Pressing the button

again will disarm the system.

Programmable Features

Step

Function

Button 1 (default) Button 2

Buttons 1&2

1. Arming Mode

Active

Passive

Passive w/countdown

2. Passive Locking

Off

On

3. Ignition Locking

On

Off

4. Arming Chirps

Normal 

Silent

5. Siren / Horn Chirps

Siren only

Horn chirps

6. Anti-Carjack Activation

Disabled

Enabled

7. Anti-Carjack Mode

Active

Passive

Full-time

8. Two Stage Disarm

Off 

On

BW1800 art dept.qxd  1/28/2004  1:30 PM  Page 6

Summary of Contents for 1R / 2-BUTTON SERIES

















Reviews: