Black Max BM10300 Series Operator'S Manual Download Page 23

Page 19 — English

WARRANTy

The EPA and SUMEC MACHINERY & ELECTRIC CO. LTD. are pleased 

to explain the emission (where “emissions” is understood to mean both 

exhaust and evaporative emissions) control system warranty on your 

2010 model year small off-road engine (SORE). In USA, new SORE must 

be designed, built, and equipped to meet the State’s stringent anti-smog 

standards. SUMEC MACHINERY & ELECTRIC CO. LTD. must warrant 

the ECS on your SORE for the period of time listed below provided there 

has been no abuse, neglect or improper maintenance of your SORE.
Your ECS may include parts such as the carburetor, fuel-injection system, 

the ignition system, catalytic converter, fuel tanks, fuel lines, fuel caps, 

valves, canisters, filters, vapor hoses, clamps, connectors, and other 

associated emission-related components.
Where a warrantable condition exists, SUMEC MACHINERY & ELECTRIC 

CO. LTD. will repair your SORE at no cost to you including diagnosis, 

parts and labor.
MANUFACTURER’S WARRANTy COVERAGE:

This emission (or emissions) control system is warranted for two years. If 

any emission-related part on your equipment is defective, the part will be 

repaired or replaced by SUMEC MACHINERY & ELECTRIC CO. LTD.
OWNER’S WARRANTy RESPONSIBILITIES:

As the SORE owner, you are responsible for performance of the required 

maintenance listed in your operator’s manual. SUMEC MACHINERY & 

ELECTRIC CO. LTD. recommends that you retain all receipts covering 

maintenance on your SORE, but SUMEC MACHINERY & ELECTRIC CO. 

LTD. cannot deny warranty solely for the lack of receipts.
As  the  SORE  owner,  you  should  however  be  aware  that  SUMEC 

MACHINERY & ELECTRIC CO. LTD. may deny you warranty coverage 

if your SORE or a part has failed due to abuse, neglect, or improper 

maintenance or unapproved modifications.
You  are  responsible  for  presenting  your  SORE  to  SUMEC  MACHIN-

ERY  &  ELECTRIC  CO.  LTD.’s  distribution  center  or  service  center 

as soon as the problem exists. The warranty repairs should be com-

pleted  in  a  reasonable  amount  of  time,  not  to  exceed  30  days.  If 

you  have  a  question  regarding  your  warranty  coverage,  you  should 

contact  Sunright  International  of  America  at  770-729-9065,  or  write 

to  the  following  address:  Sunright  International  of  America,  Inc.,  

5965 Peachtree Corners E. Ste C-3, Norcross, GA 30071. ATTENTION 

WARRANTY DEPARTMENT.
GENERAL EMISSIONS WARRANTy COVERAGE:

SUMEC MACHINERY & ELECTRIC CO. LTD. warrants to the ultimate 

purchaser and each subsequent purchaser that the SORE is:

  Designed, built and equipped so as to conform with all applicable 

regulations; and 

  Free from defects in materials and workmanship that cause the fail-

ure of a warranted part to be identical in all material respects to that 

part as described in SUMEC MACHINERY & ELECTRIC CO. LTD.’s 

application for certification.

The warranty period begins on the date the SORE is delivered to an 

ultimate purchaser or first placed into service. The warranty period is 

two years.
Subject to certain conditions and exclusions as stated below, the war-

ranty on emission-related parts is as follows:
(1) Any warranted part that is not scheduled for replacement as required 

maintenance in the written instructions supplied, is warranted for the war-

ranty period stated above. If the part fails during the period of warranty 

coverage, the part will be repaired or replaced by SUMEC MACHINERY 

& ELECTRIC CO. LTD. According to subsection (4) below. Any such part 

repaired or replaced under warranty will be warranted for the remainder 

of the period.
(2) Any warranted part that is scheduled only for regular inspection in 

the written instructions supplied is warranted for the warranty period 

stated above. Any such part repaired or replaced under warranty will 

be warranted for the remaining warranty period.

EPA EMISSION CONTROL WARRANTy STATEMENT

yOUR WARRANTy RIGHTS AND OBLIGATIONS

(3)  Any  warranted  part  that  is  scheduled  for  replacement  as  required 

maintenance  in  the  written  instructions  supplied  is  warranted  for  the 

period of time before the first scheduled replacement date for that part. 

If the part fails before the first scheduled replacement, the part will be 

repaired or replaced by SUMEC MACHINERY & ELECTRIC CO. LTD.  

according to subsection (4) below. Any such part repaired or replaced 

under warranty will be warranted for the remainder of the period prior to 

the first scheduled replacement point for the part.
(4)  Repair  or  replacement  of  any  warranted  part  under  the  warranty 

provisions herein must be performed at a warranty station at no charge 

to the owner. 
(5) Notwithstanding the provisions herein, warranty services or repairs 

will be provided at all of our distribution centers that are franchised to 

service the subject engines or equipment.
(6) The SORE owner will not be charged for diagnostic labor that is directly 

associated with diagnosis of a defective, emission-related warranted part, 

provided that such diagnostic work is performed at a warranty station.
(7) SUMEC MACHINERY & ELECTRIC CO. LTD. is liable for damages to 

other engine or equipment components proximately caused by a failure 

under warranty of any warranted part.
(8) Throughout the SORE warranty period stated above, SUMEC MACHIN-

ERY & ELECTRIC CO. LTD. will maintain a supply of warranted parts 

sufficient to meet the expected demand for such parts.
(9) Any replacement part may be used in the performance of any war-

ranty maintenance or repairs and must be provided without charge to 

the owner. Such use will not reduce the warranty obligations of SUMEC 

MACHINERY & ELECTRIC CO. LTD.
(10) Add-on or modified parts that are not exempted by the Air Resources 

Board may not be used. The use of any non-exempted add-on or modified 

parts by the ultimate purchaser will be grounds for disallowing warranty 

claims. SUMEC MACHINERY & ELECTRIC CO. LTD. will not be liable to 

warrant failures of warranted parts caused by the use of a non-exempted 

add-on or modified part.
WARRANTED PARTS:

The repair or replacement of any warranted part otherwise eligible for 

warranty  coverage  may  be  excluded  from  such  warranty  coverage  if 

SUMEC  MACHINERY  &  ELECTRIC  CO.  LTD.  demonstrates  that  the 

SORE has been abused, neglected, or improperly maintained, and that 

such abuse, neglect, or improper maintenance was the direct cause of 

the need for repair or replacement of the part. That notwithstanding, any 

adjustment of a component that has a factory installed, and properly 

operating, adjustment-limiting device is still eligible for warranty cover-

age. The following emission warranty parts list are covered (use portions 

of this list applicable to your SORE:
1)  Fuel Metering System:

 

a) Gasoline carburetor assembly and its internal components

 

b) Fuel filter (if so equipped)

 

c) Carburetor gaskets

 

d) Fuel pump (if so equipped)

2)  Air Induction System including:

 

a) Intake pipe/manifold

 

b) Air cleaner

3)  Ignition System including:

 

a) Spark plug

 

b) Ignition module/coil

4)  Miscellaneous Items Used in Above Systems:

 

a) Vacuum, temperature, and time sensitive valves and switches

 

b) Hoses, belts, connectors, and assemblies

5)  Evaporate Control:

 

a) Fuel Line

 

b) Fuel Line Fittings

 

c) Clamps

Summary of Contents for BM10300 Series





























































Reviews: