Black Horse Model Spitfire-EP BH 127 Instruction Manual Book Download Page 5 | Manualshive

Page: 5 / 22

background image

5

Spitfire - EP -

Item code: BH127

.

Instruction Manual





1) Install the rubber grommets and brass

eyelets onto the aileron servos.

I. AILERON.

1.INSTALLING THE AILERON SERVOS.

Top side

Aileron

Bottom side

C/A glue.

C/A glue.

C/A glue.

C/A glue.

Aileron.

«
...
3
4
5
6
7
...
»

Summary of Contents for Spitfire-EP BH 127























Reviews:

No comments

Related manuals for Spitfire-EP BH 127

Brand: XPower Pages: 5

Brand: Dancing Wings Hobby Pages: 2

Ultra Flash Evo

Brand: Carf-Models Pages: 5

Mini Contender Ep

Brand: Top Flite Pages: 16

G2579 The Incredibles

Brand: Fisher-Price Pages: 10

Brand: Raptor Pages: 41

Brand: Bachmann Pages: 12

Brand: Cytron Technologies Pages: 116

Brand: Faller Pages: 16

Brand: VTech Pages: 12

Spitfire F.Mk.22/24 landing flaps

Brand: Eduard Pages: 2

Peche aux Canards

Brand: Lansay Pages: 2

Brand: Mega Bloks Pages: 2

Brand: Stevens AeroModel Pages: 4

Toot-Toot Drivers 3-in-1 Raceway

Brand: VTech Pages: 16

The House of Fun M780

Brand: PalPlay Pages: 8

Mini Ultra Stick PNP

Brand: E-FLITE Pages: 28

Brand: Turnigy Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands