Black Horse Model BH167 Instruction Manual Book Download Page 3

To avoid scratching your new airplane, do not 

unwrap the pieces until they are needed for assembly. 
Cover  your  workbench  with  an  old  towel  or  brown 
paper, both to protect the aircraft and to protect the 
table. Keep a couple of jars or bowls handy to hold the 
small parts after you open the bag.

SUGGESTION

Please trial fit all the parts. Make sure you have 

the  correct  parts  and  that  they  fit  and  are  aligned 
properly  before  gluing!  This  will  assure  proper 
assembly. 

is  hand  made  from  natural 

materials,  every  plane  is  unique  and  minor 
adjustments  may  have  to  be  made.    However,  you 
should find the fit superior and assembly simple.

The painted and plastic parts used in this kit are 

fuel  proof.  However,  they  are  not  tolerant  of  many 
harsh chemicals including the following: paint thinner, 
C/A glue accelerator, C/A glue debonder and acetone. 
Do not let these chemicals come in contact with the 
colors on the covering and the plastic parts.

Caution:

This model is not a toy! 

If  you  are  a  beginner  to  this  type  of  powered 

model, please ask an experienced model flyer for help 
and  support.  If  you  attempt  to  operate  the  model 
without knowing what you are doing you could easily 

This  kit

 

 

NOTE

Black  Horse  Model  guarantees  the  component 

parts in this kit to be free from defects in both material 
and  workmanship  at  the  date  of  purchase  by  the 
purchaser.

This warranty does not cover cosmetic damage 

or  damage  due  to  acts  of  God,  accident,  misuse, 
abuse, negligence, commercial use, or modification 
of or to any part of the Product.

This  warranty  does  not  cover  damage  due  to 

improper  installation,  operation,  maintenance,  or 
attempted repair by anyone other than Black Horse 
Model.

Return only the component part that is defective 

in  materials  or  workmanship.  Please  pack  the  unit 
carefully and insure it, as this warranty does not cover 
loss or damage in transit. 

WARRANTY

DISCLAIMER

Read this disclaimer carefully before using this 

product. Please strictly follow the instruction manual 
to assemble and use this.

In that Black Horse Model has no control over the 

final  assembly  or  material  used  for  final  assembly, 
black Horse Model is not responsible for loss of use, 
or other incidental or consequential damages.

Furthermore, Black Horse Model cannot be held 

liable for personal injury or property damage caused 
by the use or misuse of Black Horse Model products. 
By the act of using the user-assembled products, the 
user accepts all resulting liability.

injure  yourself  or  somebody  else.  Please  keep  your 
safety and well-being in mind at all times.

Important:

 Before you start construction

Even  if  you  have  built  a  large  number  of  RC 

modelsplease  read  right  through  these  instructions 
and check all the kit components against the parts list. 
We have taken great trouble to keep construction as 
simple as possible, without making any compromises 
in the area of safety.

Note regarding the film covering

Minor creases or bubbles may develop in the film 

covering  due  to  major  fluctuations  in  weather 
conditions (temperature, humidity etc.); in rare cases 
you may even find a slight warp in a component. These 
minor faults are in the nature of film-covered built-up 
wooden structures, and can easily be corrected using 
a heat gun, as commonly used for modelling.

Creases: 

Blow warm air over the area and rub 

down with a soft cloth.

Wing wrap: 

Hold the panel twisted gently in the 

opposite direction to the wrap, and apply warm air to 
remove the creases from the covering.

Caution! 

do  not  heat  the  film  more  than  is 

absolutely necessary. If the air or the iron is too hot, the 
film may melt and holes may be formed.

This  model  is  highly  pre-fabricated  and  can  be 

built in a very short time. However, the work which you 
have  to  carry  out  is  important  and  must  be  done 
carefully. The model will only be strong and fly well if 
you complete your tasks competently- so please work 
slowly and accurately.

When  self-tapping  screws  have  to  be  screwed 

into  wood,  apply  a  little  white  glue  to  prevent  them 
shaking loose: just squirt white glue into the hole and fit 
the screw

§

This model is not a toy and pilots must be over the 

age of 14.

§

Be sure that no other flyers are using your radio 

frequency.

§

Do not smoke near fuel.

§

Store fuel in a cool, dry place, away from children 

and pets.

§

Wear safety glasses.

§

The glow plug clip must be securely attached to 

the glow plug.

§

Do not flip the propeller with your fingers.

§

Keep  loose  clothing  and  wires  away  from  the 

propeller.

§

Do not start the engine if people are near. Do not 

stand in line with the side of the propeller.

§

Make  engine  adjustments  from  behind  the 

propeller  only.  Do  not  reach  around  the  spinning 
propeller.

§

Moisture  causes  damage  to  electronics.  Avoid 

water  exposure  to  all  equipment  not  specifically 
designed and protected for this purpose.

SAFETY PRECAUTION:

MXS                                                                                                            Item code: BH167

3

Summary of Contents for BH167































Reviews: