background image

TOWING SAFETY

  

  Check all local and state regulations regarding towing, licensing, and 

lights before towing your log splitter.

  •

  Check before towing to make sure that the log splitter is correctly and 

securely attached to the towing vehicle and that the safety chains are 

secured to the hitch or bumper of the vehicle with enough slack to 

allow turning. Always use a Class I, 2” ball with this log splitter.

  • Do not

 carry any cargo or wood on the log splitter.

  • Do not

 allow anyone to sit or ride on the log splitter.

  •

  Disconnect the log splitter from the towing vehicle before operating it.

  •

  Use care when backing up with the log splitter in tow to avoid jack-

knifing. Allow for added length of the log splitter when turning, 

parking, crossing intersections and in all driving situations.

  •  Do not

 

exceed 45 mph when towing your log splitter.

 

      Towing the log splitter at speeds higher than 45 mph could result 

in loss of control, damage to the equipment, serious injury or death. 

Adjust towing speed for terrain and conditions. Be extra cautious 

when towing over rough terrain especially railroad crossings.

CALIFORNIA PROPOSITION 65 WARNING

This product can expose you to chemicals including lead and lead 

compounds which are known to the State of California to cause 

cancer and birth defects or other reproductive harm. For more 

information, go to 

www.P65Warnings.ca.gov

CAUTION

10

!

IMPORTANT SAFETY INFORMATION

Summary of Contents for BDKL27T

































Reviews: