11
ENGLISH
(Original instructions)
Assembly tools required (not supplied):
Phillips Screwdriver.
Fitting the guard (Fig. D, E)
Warning!
Remove the battery from the appliance before
attempting to attach the guard, edge guide or handle. Never
operate appliance without guard firmly in place. The guard
must always be on the appliance to protect the user.
u
Remove the screw from the guard.
u
Turn the trimmer upside down so that you are looking
down at the spool cap (14).
u
Turn the guard (10) upside down and slide it fully onto the
motor housing (15). Make sure the tabs (16) on the guard
engage the ribs (17) on the motor housing as shown.
u
Continue to slide the guard on until you hear it “snap” into
place. The locking tab (18) should snap into the housing
slot (19).
u
Using a phillips screwdriver, insert the guard screw and
tighten securely as shown in Figure E to complete the
guard assembly.
u
Once the guard is installed, remove the covering from the
line cut-off blade, located on the edge of the guard
Warning!
Never use the tool unless the guard is properly
fitted.
Attaching the auxiliary handle (Fig. F, G, H)
u
To attach the handle, press in on the buttons (20) on both
sides of the upper housing as shown in Figure F.
u
Position the handle as shown in Figure G (with the
BLACK+DECKER logo facing upward). Partially push the
handle on so it will hold the buttons in when you release
them with your hand.
u
Push the handle completely onto the housing and position
it slightly until it “snaps” into place.
u
To adjust the handle up or down, press in on the button
(21) and raise or lower the handle (Figure H).
u
The handle should be adjusted so that your front arm is
straight when the trimmer is in the working position.
Height adjustment (Fig. I, J–J3)
Warning!
Adjust the length of the trimmer to obtain proper
working positions shown in Figures J - J3.
u
The overall height of the trimmer can be adjusted by
loosening the height-adjust collar (6) by rotating it in the
direction of the arrow shown in Figure I.
u
Move the upper housing straight up or down. When the
desired height is achieved, tighten the collar by rotating it
opposite of the direction shown in Figure I.
Releasing the cutting line
In transit, the cutting line is taped to the spool housing.
u
Remove the tape holding the cutting line to the spool
housing.
Operation
Warning!
Always use proper eye protection.
Warning!
Before you begin trimming, only use the appropriate
type of cutting line.
Note:
Inspect area to be trimmed and remove any wire, cord,
or string-like objects which could become entangled in the
rotating line or spool. Be particularly careful to avoid any wire
which might be bent outwardly into the path of the appliance,
such as barbs at the base of a chain link fence.
Switching on and off
u
To switch the appliance on, push the lock-off button (2),
and squeeze the trigger (1).
u
To switch the appliance off, release the trigger.
Operating the trimmer (Fig. I, J–J3)
u
With the unit on, angle unit and slowly swing the trimmer
side to side as shown in Figure J.
u
Maintain a cutting angle of 5° to 10° as shown in
Figure J1. Do not exceed 10° (Figure J2). Cut with the tip
of the line. To keep distance from hard surfaces use edge
wheel (9).
u
Maintain a minimum distance of 60 cm between the guard
and your feet as shown in Figure J3. To acheive this
distance adjust the overall height of the trimmer as shown
in Figure I.
Convert to edging mode (Fig. K, L)
Warning!
The wheeled edge guide should only be used when
in the edging mode.
The trimmer can be used in trimming mode or edging mode to
trim overhanging grass along lawn edges and flower beds. For
edging, the trimmer head should be in the position shown in
Figure M. If it is not:
u
Remove the battery from the trimmer.
u
Grasp the flip-to-edge collar (7) and push down as
shown in part 1 of Figure L.
u
Rotate the flip-to-edge collar 180° counterclockwise as
shown in part 2, until the handle snaps back into the
upper half of the trimmer.
u
To return to trimming position, pull the flip-to-edge collar
down and rotate the head clockwise back to its original
position.
Note:
You will experience faster than normal cutting line wear
if the trimmer line is positioned directly over the sidewalk or
abrasive surface.
Edging (Fig. L)
Warning!
When being used as an Edger, stones, pieces of
metal and other objects can be thrown out at high speed by
the line. The trimmer and guard are designed to reduce the
danger. However,
MAKE SURE
that other persons and pets
Summary of Contents for STC1840P C
