Black+Decker FSMH13E5, Manual

Page: 7 / 12

7
ENGLISH
u
Do not use chemical cleaners with your steam mop. To
remove stubborn stains from vinyl or linoleum floors, you
can pre-treat with a mild detergent and some water before
using the steam mop.
Steam Cleaning
u
Place a cleaning pad (7) on the floor with the velcro 'loop'
side facing up.
u
Lightly press the steam mop down onto the cleaning pad
(7).
u
Connect the steam mop to the mains.
u
Press the ON/OFF button (1). It takes approximately 15
seconds for the steam mop to heat up.
u
Press the steam operate button (2). After a few seconds,
steam will start to come out of the steam head.
Note! When first filled or after running dry, it can take up to 45
seconds for steam to be produced.
u
It takes a few seconds for steam to enter the cleaning pad.
The steam mop will now glide easily over the surface to be
sanitized/cleaned.
u
Push and pull the steam mop slowly across the surface to
thoroughly steam clean each section.
u
When you have finished using the steam mop, return
the handle (9) to the upright position, making sure that it
is supported and turn it 'OFF'. Wait until the steam mop
cools down (approximately five minutes).
Caution! It is important to monitor the water level in the water
tank (4). To refill the water tank and continue to sanitize/
clean stand the mop upright making sure that the handle is
supported and turn the steam mop 'OFF'. Unplug the unit from
the electrical wall outlet, refill the water tank (4).
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (9) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
After use (Fig. G)
u
Turn the steam mop 'OFF'. turn the steam operation
button (2) to off and then press the ON/OFF button (1).
u
Wait until the steam mop cools down.
u
Unplug the steam mop from the electrical wall outlet.
u
Empty the water tank.
u
remove the cleaning pad (7) and wash it ready for next
use.
u
Wrap the power supply cable around the tidy hook (10).
Troubleshooting
If your appliance seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local BLACK+DECKER repair agent.
Problem Step Possible solution
The steam mop is not
turning on
1. Check the unit is
plugged in at the wall
socket.
2. Check the unit is
switched on using the
ON/OFF switch (1)
The steam mop is not
producing steam
3. Check the water tank
(4) is full .
NOTE: When first filled
or after running dry it
can take up to 45
seconds for steam to
be produced.
4. Check the steam
generation button is in
the ON position (2).
5. The steamer is
equipped with a
thermostat and a
thermal cut-out. If for
any reason the steamer
overheats it will switch
off. If this happens turn
off and unplug the
steamer, allow to cool
for 2 to 4 hours and
re-try.
Service Information
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efficient and reliable
product service.
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the BLACK+DECKER location
nearest to you.
NOTE
u
BLACK+DECKER’s policy is one of continuous improve-
ment to our products and, as such, we reserve the right to
change product specifications without prior notice.
u
Standard equipment and accessories may vary by country.
u
Product specifications may differ by country.
u
Complete product range may not be available in all
countries. Contact your local BLACK+DECKER dealers for
range availability.