Black+Decker BSV2020, Instruction Manual

Page: 8 / 40

English
6
Leaving the battery in the charger
The charger and battery pack can be left connected
indefinitely.
Charger Cleaning Instructions
WARNING:
Shock hazard. Disconnect
the charger from the AC outlet before cleaning. Dirt
and grease may be removed from the exterior of the
charger using a cloth or soft non-metallic brush. Do
not use water or any cleaning solutions.
Important Charging Notes
1. Longest life and best performance can be obtained if
the battery pack is charged when the air temperature is
between 65 °F and 75 °F (18 ° – 24 °C). DO NOT charge
the battery pack in an air temperature below +40 °F
(+4.5 °C), or above +104 °F (+40 °C). This is important
and will prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights;
c. Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 65 °F – 75 °F (18 ° – 24 °C);
d. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with
no adverse effect on the battery pack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
Storage Recommendations
1. The best storage place is one that is cool and dry, away
from direct sunlight and excess heat or cold.
2. For long storage, it is recommended to store a fully
charged battery pack in a cool dry place out of the
charger for optimal results.
nOTE:
Battery packs should not be stored completely
depleted of charge. The battery pack will need to be
recharged before use.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
SYMBOLS
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ..............................
volts
A ..................................amperes
Hz ................................hertz
W .................................watts
min .............................minutes
or AC ................alternating current
or DC ..........direct current
no ...............................no load speed
..............................Class I Construction
(grounded)
...............................earthing terminal
.............................safety alert symbol
..............................Class II Construction
(double insulated)
.../min or rpm. revolutions or reciprocation
per minute
Wh ..............................Watt Hours
Assembly
WARNING:
Do not attempt to modify or
repair the appliance.
Intended use
Your BLACK+DECKER 20V Max* cordless 3 in 1 stick vacuum
cleaner has been designed for dry vacuuming purposes. This
appliance is intended for household use only.
Assembly (Fig. D)
1. Align the top of the extension tube 7 with the vacuum
inlet 5 as shown in Fig. D.
2. Push the extension tube 7 onto the vacuum inlet 5 so
it locks into position.
3. Align the bottom of the extension tube 7 with the floor
brush 11 as shown in Fig. D.
4. Push the bottom of the extension tube 7 onto the floor
brush 11 so it locks into position.
5. To remove an accessory, press the accessory release
latch 8 located on the vacuum inlet or the bottom
of the extension tube and gently pull the connected
accessory off.