background image

11

CHAPTER 3: Configuration and Installation

1B.

SHM-NPR/RJ (ME821 models) only:

Get 4-wire twisted-pair cable and terminate

it with RJ-11 or (especially if the cable is shielded) RJ-12 plugs, using the pin
assignments shown in Figure 3-3 (for RJ-11 cable, substitute Pins 1, 2, 3, and 
4 for Pins 2, 3, 4, and 5 respectively) and end-to-end wiring like that shown 
in Figure 3-2 on the previous page. Also, if the cable is shielded, attach the
shield to Pin 1 or 6 

on one end of the cable only

. Plug the cable into the RJ-12

jacks on the units.

CAUTION!

Under no circumstances should you attach the cable shield to Pin 1 or 6
on both ends; this could cause damaging electrical “ground loops.”

Neither should you ever connect these units to the public switched

telephone system in any way. This could also severely damage your
equipment.

Figure 3-3. Wiring a cable for ME821 units.

2.

Both models:

Plug the units’ DB25 connectors into the RS-232 serial ports 

on the corresponding devices and tighten the mounting screws.

That’s all there is to it. Assuming your units’ DCE/DTE switches are set properly,
your SHM-NPR or SHM-NPR/RJ system should be ready for continuous operation.

PINS

FEMALE

1 2 3 4 5 6

MALE

2 (RCV-)
3 (XMT+)
4 (XMT-)
5 (RCV+)

Unit—Pins 1

and 6 connected

to frame ground

Cable—Pin 1 or 6

connected to shield

on one end only

for end-to-end

pinning, refer to

Figure 3-2 on the

previous page

Summary of Contents for SHM-NPR



















Reviews: