Black Box PSE544 User Manual Download Page 4

Page: 4 / 50

Power Switch Cabinet 4-port New Generation

Safety instructions: To be read before use!

The Power Switch Cabinet devices can only be installed by qualified people with the following installation and

use instructions. The manufacturer disclaims all responsibility in case of a bad use of the Power Switch Cabinet
devices and particularly any use with equipments that may cause personal injury or material damage.

This equipment is designed to be installed on a dedicated circuit that must have a circuit breaker or fuse

protection.

The electrical power socket used to plug the power cord of the Power Switch must be close to the Power Switch

Cabinet device and easily accessible.

Check that the power cords, plugs and sockets are in good condition.

The Power Switch Cabinet devices can only be connected to three-wire 230 VAC (50-60Hz) sockets.

Always plug the Power Switch Cabinet devices into properly grounded power sockets (two poles plus ground).

Never exceed 10 Amp total load.

If you have to replace an external fuse of an Power Switch Cabinet device, never use another type of fuse than

10A/250V T.

The Power Switch Cabinet devices are intended for indoor use only. Do NOT install them in an area where

excessive moisture or heat is present.

Always disconnect the power cord of the Power Switch if you want to intervene on the device or on the

equipment powered from the Power Switch Cabinet device.

The power outlets of the Power Switch Cabinet devices are not circuit breakers! If you want to intervene on

equipment connected to a Power Switch Cabinet device you must disconnect this equipment from the Power
Switch Cabinet device.

The Power Switch Cabinet devices contain potentially hazardous voltages. Do NOT attempt to disassemble

them.

The Power Switch Cabinet devices contain no user serviceable parts and repairs are to be performed by factory

trained service personnel only.

Summary of Contents for PSE544


















































Search results

Summary of Contents for PSE544

Reviews:

Related manuals for PSE544

Brands by name

Popular brands

Black Box PSE544, User Manual

Search results

Summary of Contents for PSE544

Reviews:

Related manuals for PSE544

Brands by name

Popular brands