Black Box ME0006A-V35 Manual Download Page 29

Page: 29 / 32

2-WIRE SHORT-RANGE DSL LINE DRIVER (HDSL WITH V.35 OR X.21)

Appendix A. V.35 Interface Pin

Assignments

Shown below are the pin assignments for the V.35 interface (M/34 female
connector), DCE orientation.

Pin #

Signal

B . . . . . . . . . . . . . . . . . . . . SGND (Signal Ground)
C . . . . . . . . . . . . . . . . . . . . RTS (Request to Send) (DTE Source)

D . . . . . . . . . . . . . . . . . . . . CTS (Clear to Send) (DCE Source)

E . . . . . . . . . . . . . . . . . . . . DSR (Data Set Ready) (DCE Source)

F . . . . . . . . . . . . . . . . . . . . CD (Carrier Detect) (DCE Source)

H . . . . . . . . . . . . . . . . . . . . DTR (Data Terminal Ready) (DTE Source)

L . . . . . . . . . . . . . . . . . . . . LLB (Local Line Loop) (DTE Source)

M. . . . . . . . . . . . . . . . . . . . TM (Test Mode) (DTE Source)

N . . . . . . . . . . . . . . . . . . . . RDL (Remote Digital Loop) (DTE Source)

P . . . . . . . . . . . . . . . . . . . . TD (Transmit Data) (DTE Source)

R . . . . . . . . . . . . . . . . . . . . RD (Receive Data) (DCE Source)

S . . . . . . . . . . . . . . . . . . . . TD/ (Transmit Data-B) (DTE Source)

T . . . . . . . . . . . . . . . . . . . . RD/ (Receive Data-B) (DCE Source)

U . . . . . . . . . . . . . . . . . . . . XTC (External Transmit Clock) (DTE Source)

V . . . . . . . . . . . . . . . . . . . . RC (Receiver Clock) (DCE Source)

W . . . . . . . . . . . . . . . . . . . XTC/ (External Transmit Clock) (DTE Source)

X . . . . . . . . . . . . . . . . . . . . RC/ (Receiver Clock) (DCE Source)

Y . . . . . . . . . . . . . . . . . . . . TC (Transmitter Clock-A) (DCE Source)

AA . . . . . . . . . . . . . . . . . . . TC/ (Transmit Clock-B) (DCE Source)

Summary of Contents for ME0006A-V35
































Search results

Summary of Contents for ME0006A-V35

Reviews:

Related manuals for ME0006A-V35

Brands by name

Popular brands

Black Box ME0006A-V35, Manual

Search results

Summary of Contents for ME0006A-V35

Reviews:

Related manuals for ME0006A-V35

Brands by name

Popular brands