14 of 15
5/4/2007
#24435
724-746-5500
blackbox.com
Item
Code
Fiber Mode Conversion Modules for the High-Density
Media Converter System II
155 Mbps (Fast Ethernet)
Multimode, 850-nm to Single-Mode, 1310-nm, 2 km
Multimode/40 km Single-Mode
ST/ST
LMC5032C
Multimode, 850-nm to Single-Mode, 1310-nm, 2 km
Multimode/80 km Single-Mode
ST/ST
LMC5034C
SC/SC
LMC5035C
Multimode, 1300-nm to Single-Mode, 1310-nm, 2 km
Multimode/40 km Single-Mode
ST/ST
LMC5028C
SC/SC
LMC5029C
Multimode, 1300-nm to Single-Mode, 1310-nm, 2 km
Multimode/80 km Single-Mode
ST/ST
LMC5030C
SC/SC
LMC5031C
622 Mbps (OC-12 ATM)
Multimode, 1300-nm to Single-Mode, 1300-nm, 40 km
SC/SC
LMC5010C
1250 Mbps (Gigabit Ethernet or OC-12 ATM)
Multimode, 850-nm to Single-Mode, 1310-nm, 2 km
Multimode/10 km Single-Mode
SC/SC
LMC5036C
Multimode, 850-nm to Single-Mode, 1310-nm, 2 km
Multimode/40 km Single-Mode
SC/SC
LMC5011C
Multimode, 850-nm to Single-Mode, 1550-nm, 2 km
Multimode/70 km Single-Mode
SC/SC
LMC5012C
Single-Strand Multimode to Single-Strand Single-Mode,
40 km (Order one of each.)
1310-nm Transmit/1550-nm Receive, SC/SC
LMC5169C
1550-nm Transmit/1310-nm Receive, SC/SC
LMC5168C
Fiber Repeater Modules
Single-Mode Plus, 1310-nm to Single-Mode Plus,
1310-nm, 40 km
SC
LE1029C
These protocol-independent modules convert multimode
to single-mode fiber. Use them to add extra distance — up to
70 kilometers (43.5 miles)— to your fiber infrastructure. Or use
them for migrating your multimode fiber infrastructure to
single mode.
Modules that support up to 155 Mbps are typically used
for Ethernet or Fast Ethernet, although, because they are
transparent to protocol, they can also be used in an OC-3 ATM
(155-Mbps) environment. Use the modules that support up to
1250 Mbps for Gigabit Ethernet or OC-12 ATM.
Use a Repeater Module anywhere you need extra distance
on a single-mode fiber link. Repeater modules support
distances of up to 40 kilometers and can be daisychained for
fiber cable runs hundreds of kilometers long.
The repeater modules retime the data signal, remove jitter,
and retransmit the amplified signal. User-selectable trans-
mission speeds range from 622-Mbps (OC-12) up to 1250-
Mbps Gigabit Ethernet.
Both Fiber Mode Conversion Modules and Fiber Repeater
Modules include FiberAlert to notify you of “silent failures”
and help you troubleshoot problems. No more time wasted
searching for them! You can check a link by observing the
status of the media converter’s Link LED.
The FiberAlert function informs you when a fault occurs
on one fiber strand and the link can’t carry bidirectional
communications between two fiber devices. With FiberAlert,
the link status of one end is mirrored at the opposite end.
If a strand isn’t available, and you have FiberAlert enabled,
the receiver end device notes the loss of the link and stops
transmitting data until it receives a signal or link pulse. This
means that the link status can be seen at
both ends
through
the respective Link LEDs, thus helping you to identify and
isolate faults anywhere in the fiber loop. FiberAlert works
even if the fiber devices are separated by great distances.
FIBER MODE CONVERSION MODULES
LMC5032C
