background image

EXPRESS 8-PORT MUX

7

2.3 Connectors and Indicators

The Mux’s LEDs and connectors are described below. Refer to Figures 2-1 and 2-2 to locate each connector or
indicator.

Figure 2-1. The Express 8-Port Mux’s Front Panel.

Figure 2-2. The Express 8-Port Mux’s Rear Panel.

Power LED

On when the Express 8-Port Mux is powered up.

TX Activity LED

On when a signal is transmitted to the fiber optic aggregate link.

RX Activity LED

On when a signal is received from the fiber optic aggregate link and the
Mux synchronizes to it.

Polling Group Status LEDs

The upper green LEDs are express mode indicators. These LEDs activate
when an express signal is detected, and they remain on until a 1-Mbps signal
is detected or a system reset occurs. The lower green LEDs are data activity
indicators. These LEDs activate when a signal is present.

Polling Group Connectors

There are two polling groups. Each polling group has been divided into two
port groups. Polling group #1 consists of ports 0 through 3 (port groups A
and B), and polling group #2 consists of ports 4 through 7 (port groups C
and D). 

Ports within a polling group must be connected to ports from a common

controller.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIII

IIIIIIIIIIIIIIIIIIIIIIIIIIIIII

POWER

Express 8 Port Mux

2X

6

GROUP D

2X

7

2X

0

GROUP A

2X

1

2X

4

GROUP C

2X

5

2X

2

GROUP B

2X

3

TX

LINK

STATUS

RX

•   •   •   •   •   •   •   •

Power

Activity LEDs

(TX and RX)

FCC label

DB25

Configuration

switches

Fiber optic

link

DC power

connection

External power supply

Product

identification

label

Polling Group #1 Status

LEDs and Connectors

Polling Group #2 Status

LEDs and Connectors

Summary of Contents for IC219A





















Reviews: