7
ENGLISH
Features
This appliance includes some or all of the following features.
1.
Hose
2.
Container handle
3.
Filter cleaning switch
4.
On/off switch
5.
Handle
6.
Cord rewind button
7.
Suction head
8.
Wheels
9.
Container
10. Extension tube
11. Airflow control switch
In addition, this appliance is supplied with some or all of the
following accessories (fig. A):
12. Crevice tool
13. Brush tool
14. Parquet floor head (VN2010 / VN2200)
15. Turbo brush (VN2200)
The parquet floor head is not included with all models. This
accessory is available from your Black & Decker dealer /
service centre (cat. no. WV100).
The turbo brush is not included with all models. This
accessory is available from your Black & Decker dealer /
service centre (Cat. No. WV200).
Assembly
Connecting the hose (fig. A)
X
Insert the hose connector (16) into the inlet (17) of the
appliance.
X
Line up the hose connector tabs with the slots in the inlet.
X
Slide the hose further until the release buttons (18) (2
positions) click into place.
X
To disconnect the hose, press the release buttons (18) (2
positions) and pull out the hose.
Mounting the extension tube (fig. A)
X
Press the lock button (19) and slide the hose nozzle (20) into
the tube (10) until it clicks into place.
X
To remove the tube (10), press the lock button and pull the
hose nozzle (20) out of the tube.
Mounting the suction head (fig. A)
The suction head (7) allows for vacuuming on carpet and
hard surfaces (e.g. laminate and tiles).
X
Press the lock button (21) and slide the tube (10) into the
head (7) until it clicks into place.
X
To remove the head (7), press the lock button (21) and pull
the tube (10) out of the head (7).
VN2010/VN2200 - Mounting the parquet floor head (fig. A)
The parquet floor head (14) allows for vacuuming on wooden
and polished surfaces.
X
Press the lock button (21) and slide the tube (10) into the
head (14) until it clicks into place.
X
To remove the head (14), press the lock button (21) and pull
the tube (10) out of the head.
VN2200 - Mounting the turbo brush (fig. A)
The turbo brush (15) allows for vacuuming on cut pile
carpeting.
The brush is particularly useful for picking up hair, threads,
etc., as well as for refreshing trodden-down carpet pile.
X
Press the lock button (21) and slide the tube (10) into the
head (15) until it clicks into place.
X
To remove the head (15), press the lock (21) button and pull
the tube (10) out of the head.
Mounting accessories (fig. A)
The crevice tool (12) allows for vacuuming in narrow and
hard to-reach places. The brush tool (13) allows for
vacuuming on furniture, blinds, curtains, windows and stairs.
The accessories can be mounted on both the hose (1) and the
tube (10).
X
Press the lock button (19 or 21) and slide the accessory onto
the hose nozzle (20) or the tube (10).
X
To remove an accessory, press the lock button (19 or 21)
and pull the accessory off.
When not in use, the accessories can be stored on the
accessory holder (22). The accessory holder is stored on the
hose nozzle. This is clipped into place, to remove pull way
from the hose nozzle. The tools are stored as shown in fig. A.
Use
Unwinding and rewinding the cord
The cord rewind button (6) can be operated by hand or foot.
X
Before use, pull a sufficient length of cord from the back of
the appliance.
X
After use, press the cord rewind button (6) to store the cord
back into place. Manually guide the cord to ensure it does
not swing back. Ensure the plug is correctly located.
Adjusting the length of the tube (fig. B)
The extension tube (10) is made up of three pieces.
X
To extend the middle / lower two pieces, press the lower
adjustment button (23) and slide out the tube fully until it
clicks into place.
X
The upper two pieces can be adjusted in 11 steps. Press the
upper adjustment button knob (24) and slide the tube to the
desired length. Make sure that the tube clicks into place.
