background image

8

ENGLISH

(Original instructions)

vibrating abnormally.

Wear stout shoes or boots to protect 

your feet.

Wear long trousers to protect your legs.

Before using the appliance, check that 

your cutting path is free from sticks, 

stones, wire and any other obstacles.

Only use the appliance in the upright 

position, with the cutting line near the 

ground. Never switch the appliance on 

in any other position.

Move slowly when using the appliance. 

Be aware that freshly cut grass is 

damp and slippery.

Do not work on steep slopes. Work across 

the face of slopes, not up and down.

Never cross gravel paths or roads 

while the appliance is running.

Never touch the cutting line while the 

appliance is running.

Do not put the appliance down until the 

cutting line has come to a complete 

standstill.

Use only the appropriate type of 

cutting line. Never use metal cutting 

line or fishing line.

Be careful not to touch the line 

trimming blade.

Keep hands and feet away from the 

cutting line at all times, especially 

when switching on the motor.

Before using the appliance and after 

any impact, check for signs of wear or 

damage and repair as necessary.

Never operate the appliance with damaged 

guards or without guards in place.

Take care against injury from any 

device fitted for trimming the filament 

line length. After extending new cutter 

line always return the machine to 

its normal operating position before 

switching on.

Always ensure that the ventilation slots 

are kept clear of debris.

Additional safety instructions for 

batteries and chargers
Batteries

Never attempt to open for any reason.

Do not expose the battery to water.

Do not store in locations where the 

temperature may exceed 40 °C.

Charge only at ambient temperatures 

between 10 °C and 40 °C.

Charge only using the charger 

provided with the tool.

When disposing of batteries, follow 

the instructions given in the section 

"Protecting the environment".

Chargers

Use your BLACK+DECKER charger 

only to charge the battery in the tool 

with which it was supplied. Other 

batteries could burst, causing personal 

injury and damage.

Never attempt to charge non-

rechargeable batteries.

Have defective cords replaced 

immediately.

Do not expose the charger to water.

Do not open the charger.

Do not probe the charger.

The charger is intended for 

indoor use only.

Read the instruction manual 

before use.

Summary of Contents for ST1823
















Reviews: