background image

5

WARNING:

 Never attempt to 

open the battery pack for any reason. If battery 

pack case is cracked or damaged, do not insert 

into charger. Do not crush, drop or damage 

battery pack. Do not use a battery pack or 

charger that has received a sharp blow, been 

dropped, run over or damaged in any way (i.e., 

pierced with a nail, hit with a hammer, stepped 

on). Damaged battery packs should be returned 

to service center for recycling.

WARNING:

 Fire hazard. Do 

not store or carry battery so that metal 

objects can contact exposed battery 

terminals. For example, do not place battery 

in aprons, pockets, tool boxes, product kit 

boxes, drawers, etc., with loose nails, screws, 

keys, etc. Transporting batteries can 

possibly cause fires if the battery 

terminals inadvertently come in contact 

with conductive materials such as keys, 

coins, hand tools and the like. The US 

Department of Transportation Hazardous 

Material Regulations (HMR) actually prohibit 

transporting batteries in commerce or on 

airplanes (i.e., packed in suitcases and carry-

on luggage) UNLESS they are properly 

protected from short circuits. So when 

transporting individual batteries, make sure 

that the battery terminals are protected and 

well insulated from materials that could 

contact them and cause a short circuit. 

NOTE:

 Lithium-Ion batteries should not 

be put in checked baggage.

STORAGE RECOMMENDATIONS 

1. The best storage place is one that is 

cool and dry away from direct sunlight and 

excess heat or cold.

2. Long storage will not harm the battery 

pack or charger.

CHARGING PROCEDURE 

BLACK+DECKER chargers are designed to 

charge BLACK+DECKER  battery packs in 3-4 

hours depending on the pack being charged. 

1. Plug the charger into an appropriate outlet 

before inserting the battery pack.

2. Insert the battery pack into the charger. 

 3. The green LED will flash indicating that 

the battery is being charged.

 4. The completion of charge is indicated by 

the green LED remaining on continuously. 

The pack is fully charged and may be used at 

this time or left on the charger.
Recharge discharged batteries as soon as 

possible after use or battery life may be 

greatly diminished. For longest battery life, 

do not discharge batteries fully.

LEAVING THE BATTERY IN THE CHARGER

The charger and battery pack can be left 

connected with the green LED glowing 

indefinitely. The charger will keep the 

battery pack fresh and fully charged. 

IMPORTANT CHARGING NOTES

1. Longest life and best performance can 

be obtained if the battery pack is charged 

when the air temperature is between 65°F 

and 75°F (18°- 24°C). DO NOT charge the 

battery pack in an air temperature below 

+40°F (+4.5°C), or above +105°F (+40.5°C). 

This is important and will prevent serious 

damage to the battery pack.

2. The charger and battery pack may 

become warm to touch while charging. 

This is a normal condition, and does not 

indicate a problem. To facilitate the cooling 

of the battery pack after use, avoid placing 

the charger or battery pack in a warm 

environment such as in a metal shed, or an 

uninsulated trailer.

3. If the battery pack does not charge properly:

 

a. Check current at receptacle by 

plugging in a lamp or other appliance

 b. 

Check to see if receptacle is 

connected to a light switch which turns 

power off when you turn out the lights. 

 

c. Move charger and battery pack to a 

location where the surrounding air  

 temperature is approximately 65°F - 

75°F (18°- 24°C). 

 

d. If charging problems persist, take 

the tool, battery pack and charger to 

your local service center.

4. The battery pack should be recharged 

when it fails to produce sufficient power on 

jobs which were easily done previously. 

DO NOT CONTINUE to use under these 

conditions. Follow the charging procedure. 

You may also charge a partially used pack 

whenever you desire with no adverse affect 

on the battery pack.

5. Foreign materials of a conductive nature 

such as, but not limited to, steel wool, 

aluminum foil, or any buildup of metallic 

particles should be kept away from charger 

cavities. Always unplug the charger from 

the power supply when there is no battery 

pack in the cavity. Unplug charger before 

attempting to clean.

6. Do not freeze or immerse charger in 

water or any other liquid.

WARNING:

 Shock hazard

Do not allow any liquid to get inside charger. 

Never attempt to open the battery pack for 

any reason. If the plastic housing of the 

battery pack breaks or cracks, return to a 

service center for recycling.

SAVE THESE INSTRUCTIONS

Summary of Contents for LSW221

































Reviews: